Can we define the external quantum efficiency as the (number of photons emitted/ electrons injected) for n LED device?

08 July 2020 1 3K Report

I have come across the definition for EQE as the number of radiative recombination events out of the total number of recombination events in the LED. But is it safe to say that EQE = number of photons / electrons injected in the device?

Pravin Ramdas Yawale

External quantum efficiency term is define for individual LED. For LED luminary lumen per watt this quantity is used represent its output effciency.

Badges
Science topic

Similar topics
Solid State Physics
Devices

More Jitesh Pandya's questions See All

How to know if Zinc Oxide is coated on the glass substrates?

Hello all I have prepared Zinc Oxide nanoparticles using sol gel synthesis. I tried to coat the ITO and glass substrates with the ZnO nanoparticles ( dispersed in ethanol). But I am not sure if...

08 December 2020 3,692 8 View

Which PEIE to use?

Hello all Thanks for answering my previous questions. I am making perovskite LED and intend to use PEIE on zinc oxide layer as ETL. But I am not sure what version of PEIE to us. There is the one...

08 November 2020 5,710 3 View

Zno NPs seperation?

Thanks a lot for your answers. I have one more question: after synthesizing ZnO nanoparticles , I am not able to separate from the original solution (dispersion actually). The recipe is as...

23 October 2020 9,857 8 View

How to do PBABr synthesis?

I am following this recipe for PBABr synthesis. I added HBr (48 wt % in H2O) to Methanol and PBA solution at 0 degrees celsius. But after 2 hours of stirring I am not able to see precipitates. I...

08 October 2020 6,485 4 View

ZnO and PBABr synthesis?

Hello all, I want to synthesize ZnO nanoparticles and PBABr in my lab for my LED project. I know the method, but I am not sure how can I check(even visually) that I have arrived at the correct...

27 September 2020 5,334 7 View

MoO3 RF Sputtering?

Hello all, I have to do RF sputtering for MoO3 for my LED project. But I have come across many recipes for reactive RF sputtering of MoO3 ,using Mo as a target and Oxygen as the reactive gas But...

16 September 2020 5,222 2 View

Any method for preservation of Bombay duck (Harpadon nehereus) during rainy days?

Other than chilling method for preservation of Bombay duck (Harpadon nehereus) during rainy days?

14 September 2020 5,135 6 View

Which one is best technique for drying of Fish?

Drying method for commercial production of dried fish.

09 September 2020 7,151 6 View

How to obtain corrected PL spectrum?

Hello all, I am intending to measure the PL spectra for my perovskite samples. How can we obtain a corrected PL spectra in the spectrometer, independent of the photoresponsivity of the silicon...

29 June 2020 7,298 5 View

How to resolve FLIR bad quality output issue?

Hello, I have a FLIR VUE PRO R 640 Thermal Camera fixed mounted on my custom Drone. For the last couple of months, this sensor is not capturing the quality data and the use of FLIR TOOLS with...

26 November 2019 4,718 3 View

What is the most Operating System (OS) which can be INSTALL on Tiny hard devices like Raspberry Pi (RPi) hardware ?

I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...

03 March 2021 1,931 5 View

Does any one know how i can prepare liver tissue with transmission electron microscope with good fixation?

i have problem in preparation of liver tissue with bad cell organelles and how i can adjust osmolarity

03 March 2021 8,890 1 View

I need to image mesoporous silica nanoparticles that are in ~100 nm size and do high resolution TEM to look at mesopores. what grids should I use?

Need to image mesoporous silica nanoparticles using the TEM. Also, need high resolution TEM images to see the mesoporous structure. Kindly suggest what kind of grids to use. Thanks, Shatadru

02 March 2021 1,787 2 View

Waters 2707 HPLC autosampler problem?

I am using a 2707 waters HPLC device. When I try to inject a sample, it says missing plate or rack. I changed the needle and calibrated its position but I still get the same problem. I even get...

02 March 2021 1,408 1 View

Shall I skip the measurement model in SmartPLS?

Hello everyone, I had run a mediation model in SmartPLS using questionnaires that were already validated among my statistical population. A professor who edited my paper -though she is not...

01 March 2021 3,052 3 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

SEM or Multiple Regression for an analysis without Latent Variables?

Hello, I have three hypothesis to test, all with the same IV. I am testing if the effect of the IV on the first DV is mediated by awe. I am then measuring whether the effect of the IV on a...

26 February 2021 8,399 5 View

Gas sensor response and recovery time independant of flow rate and chamber volume?

I am trying to obtain the response and recovery times for my gas sensor device. It appears the the response/recovery times are primarily dependant on the flow rate of the gas I inject into the...

26 February 2021 1,511 3 View

How to calculate battery consumption for IoT device?

Hi, everyone I'm working on a privacy-preserving algorithm that will apply to IoT devices. So, I need to measure the power consumption by implementing this algorithm. Any suggestion, advice,...

25 February 2021 8,749 6 View