Can the set up files created for openfoam v4.0 (from .org) can be used for openfoam 1906 (from .com)?

I noticed that openfoam software is provided by two different organisations 1. ESI group 2. OpenFOAM foundation. My doubt is if the cases are set based on the version provided by openfoam...

31 December 2019 4,726 2 View

Is meshgems (add on module in salome) is good for hexmeshing of fluid domain to be run in openfoam?

Hi I'm currently using snappyhex mesh for meshing my fluid domain to run simulation in openfoam. I found salome is better free alternative to snappyhexmesh, but the time required by the mesh...

10 November 2019 1,568 1 View

Why the flow direction seems fixed along 'x' axis in OpenFOAM 6 (I apologise I found no issues with velocity compoent)?

I recently updated my OpenFOAM version 4.0 to 6. I'm facing an issue in the direction of flow. My flow is always pointing in x direction. Hence I tried to change the flow axis in a tutorial...

08 September 2019 5,629 1 View

Is just the pressure raise on closing the valve causes water hammering?

I recently saw this lecture from NPTEL on water hammering. I suppose example used for explaining the wave motion is widely used. (flow from a reservoir and valve...

07 August 2019 1,756 4 View

How to determine the suction pressure of multiple pumps operating in parallel?

Hi Im doing an analysis on total head developed by a pumping station that has 6 pumps. We have measurement reading for pressure on delivery side, but unfortunately volume flow rate is measured at...

09 October 2018 4,197 1 View

How to determine the head rise in vertical turbine pump?

Dear all, I'm looking to apply Bernoulli's principle to determine the head rise in the pump. Since most of the lectures are based on centrifugal pump, there is a suction pipe and delivery pipe,...

09 October 2018 10,047 0 View

What is the difference between freestream BC and inletoutlet BC?

08 September 2018 1,089 0 View

How to connect between Simulink 2014a and Code Composer Studio V5?

Hi I'm working on active noise cancellation using DS TMS320C6713. I have created the model in simulink but I'm not sure how to transfer the mdl file into CCS v5.

06 July 2018 6,210 0 View

Why the hydrostatic pressure at outlet is not chaning based on velocity and total pressure?

02 March 2018 3,670 3 View

How to set up domain for cfx non premixed combustion modelling?

Hi all I'm trying to remodel pool fire modelling based on this paper "LNG pool fire simulation for domino effect analysis"...

11 December 2017 954 2 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

The procedure compute?

02 March 2021 5,204 3 View

Is there a powerful system for the security of the systems distributed on IoT systems?

Is there a powerful system for the security of the systems distributed on IoT systems?

02 March 2021 3,858 10 View

Which is suitable for use with Python? MySQL or SQL Server?

Which is suitable for use with Python? MySQL or SQL Server? What is your suggestion?

01 March 2021 3,422 3 View

If you haven't computer? how you show the photons to pupils?

Educational Process

01 March 2021 1,827 1 View

Please can i get topic and materials that will relate computer with telecommunication companies?

I am a master student and i am working on my research, so I am a bit confuse don't really know how to match computer with telecommunication as a topic

28 February 2021 7,039 6 View