What is the role and mechanism of LPSO phase in mechanical and corrosion behavior of Mg alloy?

04 May 2017 293 3 View

FFT image in TEM?

03 April 2017 4,000 1 View

FFT image in TEM?

How Can I obtain the information from FFT image in TEM?

31 December 2016 5,321 2 View

In your opinion, in produce of nanocomposite with Ti ( microparticles) matrix and reinforce particles (oxide nano particles for example Al2O3, SiO2, ?

In your opinion, in produce of nanocomposite with Ti ( microparticles) matrix and reinforce particles (oxide nano particles for example Al2O3, SiO2, ZrO2 and ......) by mechanical milling...

04 May 2016 7,335 2 View

In your opinion, in ball milling of aluminum powder with SiC nanoparticles what type of PCA to use?

Read 5 answers by scientists with 4 recommendations from their colleagues to the question asked by Mohammad Alipour on Apr 4, 2016

03 April 2016 8,123 5 View

In your opinion, in ball milling of aluminum powder with SiC nanoparticles what type of PCA to use?

In your opinion, in ball milling of aluminum powder with SiC nanoparticles what type of PCA to use?

02 March 2016 1,133 0 View

What is the advantage of silicon carbide nanoparticles than the other nanoparticles?

What is the advantage of silicon carbide nanoparticles than the other nanoparticles?

01 February 2016 1,576 3 View

What is the mechanism of distribution of nanoparticles by ultrasonic waves?

What is the mechanism of distribution or dispersion of nanoparticles by ultrasonic waves?

07 August 2015 2,144 9 View

How can I determine amorphous to crystalline ratio in an XRD pattern?

How to determine amorphous to crystalline ratio in an XRD pattern?

02 March 2015 7,089 10 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View