What is the most reliable source to get Impact factor of journals?

Source to get Impact factor of journals

01 March 2021 6,654 2 View

Is anyone familiar with the cyclic compressive fatigue testing (BS EN 12697 - 25) ?

I would like to get more information on the cyclic compressive fatigue testing (BS EN 12697 - 25) which is typically done for bituminous material in pavement design. Any one can advise on the...

28 February 2021 2,004 3 View

Why initial concentration of Pb not the same as calculated one when testing using AAS?

I am currently doing research on the adsorption of heavy metal using magnetic reduce graphene oxide. I use AAS to determine the concentration of the heavy metal. I prepare the Pb solution with...

26 February 2021 9,580 4 View

Stress/strain tensors decomposition ???

25 February 2021 6,760 1 View

Best FE Program for Concrete Strengthened with FRP Sheets?

Colleagues, I have been using ANSYS to model concrete strengthened FRP sheets, but less than happy with it. Any has recommendation for efficient, easy to use FE program for modelling concrete...

22 February 2021 7,528 3 View

Any information about dinitrosalisylic acid reagent end point color stability ?

I work on estimation of alpha amylase activity using dinitrosalisylic acid reagent If i put the reagent to stope the enzymatic reaction and allow the reagent to react with the produced reducing...

17 February 2021 7,402 4 View

Using liquids as superstrate in Fabry-Perot Cavity Antenna?

Hi, A Fabry Perot Cavity allows to increase the directivity of a low gain antenna by putting in the top of cavity a superstrate with high permittivity such as a ceramic (er=10.2). However,...

09 February 2021 6,799 8 View

Experiment statistical analysis?

07 February 2021 3,635 3 View

Distribution of modes fields ?

Hi, We find a specific distribution of electric fields in structure for different frequencies which can be seen using em solvers and known as modes. I would like to know how we can choose the...

04 February 2021 10,043 3 View

Greetings Doctors, If i did a same experiment for a 2 populations and i need to publish this work in a 2 different papers?

If i did a same experiment for a 2 populations and i need to publish this work in a 2 different papers can i use the same word in the writing of these 2 papers or this would considered as...

04 February 2021 4,648 4 View

For acid treated montmorillonite clays what will be the result of surface area?

The organo montmorillonite nanoclays modified with octadecylamine were used for the experiment. After acid treatment, the surface area will be increase. However, in my experiment, the surface area...

10 February 2021 1,581 3 View

What could be the reason for XRD pattern starting from very high counts/intensity at 3 degree 2 theta?

I am working on XRD analysis of the clay minerals from the sea sediments. My XRD pattern shows very high counts at the start of the XRD pattern (3 degree 2 theta) which is very unusual. The counts...

31 January 2021 4,493 9 View

Is it possible to prepare clay minerals by mixing pure oxides of required elements? What would be theoretical difficulties with it?

Practically this is not at all necessary. But theoretically, would hydrous/hydrothermal synthesis be enough (like mix 1 mole alumina gel and 4 mole silica gel and gently heat) or would it require...

26 January 2021 6,403 3 View

What is the difference between soluble ions and exchangeable cations? And How to determine each of them?

I used percolation columns to reclamation saline-sodic clay soils . And my question is, What is the difference between soluble ions and exchangeable cations?

18 January 2021 6,868 3 View

Is there a way to identify the clay mineral based on the Si:Al ratio that has been obtained through EDAX analysis?

I have come through a few literature,were the presence of particular clay mineral has been validated through the Si:Al ratio obtained from EDAX analysis. But, I would like to understand the basic...

08 January 2021 5,982 6 View

What is the relationship between Sensitivity ratio and liquidity index especially for quick clay?

Also if anyone can share latest research regarding Geo-disaster of quick clay except in Norway? Thanks Kind Regards Dr. Khan

05 January 2021 4,645 3 View

How to analysis orientation molecule adsorbed on mineral clay molecular dynamics using gromacs?

I'm still confused. Whether to determine the methylene blue orientation, I have to use the order parameter (gmx order) or the gmx angle? I want to determine the orientation of the methylene blue...

31 December 2020 2,386 3 View

Please suggest ways to perform Discreet Element Modeling (DEM) on stabilized clayey soil; is it effective to simulate clay for DEM analysis?

I am looking for answer considering modelling in PFC

26 December 2020 5,509 1 View

How can I realise the separation of clay mineral part from soil ? and what is this process called ?

Hey; I am looking to work on clays in my soil samples, So I need to extract them first. I know that I should first remove all the bending agents that make the clay sheets stay connected like (...

24 December 2020 7,082 2 View

Not sure if my XRD data needs to be corrected for clays?

Hi I am currently trying to determine the mineral constituents of my samples. And I have been reading up on XRD a bit more and am wondering if my XRD plots will be okay to analyse as they are or...

18 October 2020 6,295 14 View