06 December 2023 0 7K Report

I need the full Book for these models by Nygaard, Theoretical Model of Research Productivity And Technology Acceptance Model by Davis, 1989

More Philip Gana Malgwi's questions See All
Does anyone know of a predictable relationship beween surface gravity and atmospheric composition?

The attached file demonstrates that there is a predictable relationship between the structural density of a terrestrial body and its none-rotating surface gravity. Using Newton's gravity law of...

26 February 2021 2,317 3 View

What is the chemical composition of chlorellin?

The chlorellin is the chemical compound which is first extracted from Chlorella vulgaris by Pratt in 1944. Spoehr in 1949 wrote that it is a mixture between fatty-acids and hyrdocarbons and its...

25 January 2021 8,538 1 View

Is it possible to dynamically adjust the data rate of a wireless node using TSCH protocol in Link Layer?

I'm currently learning about rate-based congestion control for industrial wireless sensor network. Suppose there is a network consisting of several sensor nodes and one coordinator node connected...

12 November 2020 373 2 View

How long can PBMCs survive outside of an incubator in R-10 culturing medium?

I have been running ELISPOTS with not much success recently due to high levels of background. After testing everything from the DMSO used in peptide stimulation to the FBS in the culturing medium,...

15 October 2020 849 3 View

How dissolve Hyaluronic acid with consistent viscosity?

I'm trying to dissolve HA in PBS or cell media, 20 mg/ml, but gets inconsistent viscosity on my solutions. Some samples are very viscous while others are very liquid. The HA functionalized with a...

30 June 2020 4,075 3 View

What does it mean if an anaplastic thyroid cancer has no mutations or fusions in a comprehensive PCR analysis?

The tumor has p53 possitivity, but a comprensive PCR analysis showed no mutations in tp53.

30 March 2020 884 3 View

What does a Negative Phi and Cramers V coefficients imply?

From the way we define the phi and Cramers V and from my theoretical knowledge, I expect Phi coefficient and Cramer's V to bare positive values. In a recent analysis using SPSS 22.0, Negative...

22 March 2020 4,064 6 View

How do I obtain Total Faradaic effeciency close to 100%?

After CO2 Electrochemical reduction on 6 samples, i obtained both gaseous and liquid products from GC-MS and NMR respectively. i quantified the liquid products by integrating each peak. for...

14 December 2019 5,479 4 View

Entrepreneurial Orientation Measurement Results?

Hello, I am looking for a review of EO measurement results via the Miller/Covin Slevin scale. I mean the actual values for innovativeness, risk and proactiveness. There are a number of papers who...

18 November 2019 8,474 3 View

Human-centered Design Questionnaire?

Hello, I'm searching for a [validated] Human-centered Design questionnaire. I've been searching in the Industrial Design and Human-computer Interaction literature, but have come up short. The...

26 October 2018 4,853 4 View

Similar questions and discussions
MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Could you recommend any books about Number Theory?

Beginner level books. High level books. Analytical Number Theory. Algebraic Number Theory. Combinatorical Number Theory. Books about partitions. Books about primes.

03 March 2021 7,174 5 View

What kind of intervention will be relevant to increase motivation among young sport trainees?

Any suggestion on what book to read is also welcome.

03 March 2021 1,646 4 View

How the parameters (such as Mw, Chemical bonds, polymer bland and so on) affect the mechanic property of polymer (such as storage, loss modulus) ?

Anyone can recommend any books on such topics? Thanks in advance.

02 March 2021 8,457 2 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close