Can someone explain me circled circuit operation of 2 switch forward converter in below figure?

More Jaikumar M's questions See All

Is there any cases algae not using the nutrient from the wastewater and grow normally?

I am working on microalgae cultivation using waste water. The initial concentration of nutrients were less but the microalgae has achieved biomass growth of 2 g/L. The final concentration of...

08 August 2024 4,812 2 View

I have calcined my catalysts without flowing air from the compressed air cylinder will there be any problem with my reaction if i use that catalysts?

FYI Catalyst is MFI zeolite Si/Al = 140,25.40.11.5,15 I am using this catalyst to study methanol to DME conversion

25 July 2024 2,486 2 View

How can I measure arsenic concentration in a patient blood?

I intend to get an economical and accurate LAB TEST to measure arsenic concentration in blood sample.

23 July 2024 3,654 2 View

It is possible to conduct a structured written interview for a qualitative study?

In your opinion, I would like to know if a qualitative study with a structured interview can be conducted in writing. In other words, we sent out open questions and asked the interviewees to...

11 July 2024 4,163 4 View

What is Differential-Fed in microstrip patch ant? How it is design in CST studio? What is process and procedure to do Differential-Fed in CST studio?

What is Differential-Fed in microstrip patch antenna ? How it is design in CST studio? What is simulation process and procedure to do Differential-Fed in CST studio ?

08 July 2024 7,464 1 View

How to know the TM/TE modes in antenna design in CST studio?

How to know the TM/TE modes in antenna design in CST studio? Example: TM01 ,TM02 ,TM10, TM12, TM30 like this... how can identify the antenna is operate the above said mode? can any one explain...

08 July 2024 6,609 2 View

What is co-polarization and cross polarization? How can plot it from CST studio?

what is co-polarization and cross polarization? How can plot it from CST studio? what are steps and process for find out co-polarization and cross polarization from CST studio?

08 July 2024 7,869 1 View

Why in some degradation experiment the results doesn't fit first or second order kinetics ?

In an antibiotic degradation experiment using metals carbon composites to activate PMS, the results doesn't fit pseudo first or second order kinetics however the degradation efficiency is very...

26 June 2024 6,941 3 View

Why carrier Concentration decreases while increasing Temperature ?

Hi All . Recently, I conducted Hall measurement experiments at high temperatures on highly p-doped diamond with a doping concentration of 2.5×10^20 cm−3 During these experiments, I observed two...

23 June 2024 4,763 0 View

What are the best practices for increasing earth biomass?

I'm thinking of how to increase biomass to replace plastic and industrial waste.

23 June 2024 1,871 4 View

How to conduct a sensitivity power analysis for Kendall's Tau?

Is there a straightforward way to conduct a sensitivity power analysis for a Kendall's Tau correlation? I was considering using the sensitivity setting and "Correlation: point biserial model" test...

28 July 2024 6,133 8 View

Terrorism, a natural inclination of all animal species?

There are many types of symbolic judgements. For example, when an Israeli pilot flattens the home of a Palestinian family (even if they are forewarned), it is natural for them to experience shock...

28 July 2024 2,610 1 View

How can I calculate minimal sample size using G Power?

I am conducting a study aimed at exploring the correlation between introversion and social phobia among Lebanese adults. I need to calculate the minimal sample size using G Power, but I'm not sure...

19 July 2024 6,048 1 View

How can we calculate the polygon scanner speed by changing the supply voltage?

I am using a polygon mirror scanner that have 6 facets and the dc brushless motor speed was given 10,000 RPM. Now I want to know how to calculate the polygon speed if I change the power supply...

11 July 2024 5,942 1 View

What should I upgrade in my computer to speed up simulation in CST?

I want to reduce simulation time in CST for frequency domain solver by upgrading my computer. I already have discrete GPU but it doesn't seem to make any difference at all compared to integreted...

10 July 2024 2,789 4 View

What is Printed Circuit Board (PCBs)?

Dear Members, We are conducting a research survey on the Printed Circuit Board (PCBs) industry and would greatly appreciate your valuable input. To participate, click the following...

09 July 2024 4,936 1 View

Full Enquiry On Biomass Energy In engineering Technology?

How is biomass energy essential in the power generation in a country.

08 July 2024 9,477 2 View

How to interpret Sensitivity Power Analysis for 2x2x2 repeated measures ANOVA?

I want to calculate the sensitivity using G*Power. If I have understood correctly G*Power gives me the detectable effect size for three-way interactions if I enter the number of groups (meaning...

08 July 2024 8,653 2 View

How can we do power system state estimation using ML?

I am trying to do a matlab project on power system state estimation. I am doing using WLS,EKF and particle filter method and then comparing these all. To minimize the error can we use Machine...

04 July 2024 6,845 0 View

How can we reduce the porosity of tungsten oxide (WO3) thin films during DC sputtering deposition (target: W, power: 100 W, 75 W, and 50 W)?

We are fabricating a tandem structure where a ~50 nm thick WO3 film is deposited between two metal films using DC sputtering. We use a mixture of Ar and O2 gases at different flow rates while...

01 July 2024 2,686 2 View

Battula santhosh kumar

the following link & attachment would help you

http://www.eetimes.com/document.asp?doc_id=1273232

this link will also help you

http://kpubs.org/article/articleMain.kpubs?articleANo=E1PWAX_2015_v15n3_602

Jaikumar M

Thank you. I'm not looking for working of 2 switch circuit. There is an extra added circuit for which I'm expecting explanations