Can someone can recommend a mask material for Lithium sputtering? The mask will be place on top of the substrate.

07 July 2017 0 8K Report

I am planning to coat lithium films by sputtering, can anyone suggest what material I should use to construct a mask on top of the substrate?

Badges
Science topic

More Enrique Valderrama's questions See All

How to clean mica substrates in the industry?

I saw many advice to cleaved the surface using tape, but I doubt this is the standard in the industry. I understand you want to dont use water, but what about another solvents? Anyone can provide...

06 July 2017 2,553 4 View

Can someone working on the public health sector provide the data which justify which vaccines need to be used per country?

The number of vaccines and doses have been increased during the last 30 years tremendously, I support the uses of vaccines, but I am curious about the DATA which justifies, how many and how much....

04 May 2017 1,288 4 View

Which opensource software can be use for DATA ANALYTIC'S?

Or what opensource is competitive with jmp ? http://www.jmp.com/

09 October 2014 2,347 0 View

How does one do dip coating or drop-drying of silver nanoparticles?

I am planning to study the antimicrobial properties of glass coated with silver nanoparticles. I would like to do it with dip coating. Can anyone help with their expertise?

10 November 2013 5,620 4 View

Problems about acousto-optic coupling in Comsol, how to check whether the moving mesh is correct?

I’m trying to reproduce the acousto-optic coupling simulation in the paper Frequency–angular resolving LiDAR using chip-scale acousto-optic beam steering. LNOI(lithium niobate on insulator) is...

13 August 2024 9,795 0 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

What is the reason I get 400nm nanoparticles using an extruder with 200 nm membrane for cell membrane coating?

I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...

30 July 2024 3,294 3 View

What is the main used curing agent for epoxy based coating?

I am trying to coating metal oxide into steel substrate, for better sticking planning to utilse epoxy based, Could you please suggest suitable curing agent for the coating purpose

25 July 2024 438 3 View

How to scrape off the surface layer of compound sputtering targets as with multiple usage top layer's stoichiometry changes from the original target?

I am experiencing this for the Bi2Se3 sputtering target. Initially, even if the target was 2:3 in Bi : Se, with a few sputtering runs, due to the high escaping tendency of selenium, the top layer...

23 July 2024 1,649 1 View

How do you get pure primary macrophage cell culture?

I have been harvesting monocyte-derived macrophages from buffalo and cattle fresh whole blood using the same protocol for years and getting good macrophage cultures. Below is the protocol that I...

23 July 2024 4,074 2 View

Optimal condition for depositing FTO target 95:5% using sputter technique?

Hello I want to know about the sputtering condition of depositing FTO from target 95:5%. I tried with RF sputter in pressure 2.5Pa and 100 sccm Ar at room temperature but it showing no...

21 July 2024 1,680 2 View

Look for qualified candidates of Visiting Scholars to Southwest Jiaotong University?

We invite qualified candidates of Visiting Scholars to engage in research collaboration or deliver lectures on their research, with travel expenses covered. The visiting period is flexible,...

20 July 2024 1,165 1 View