01 January 2017 1 5K Report

Glass Furnace, Simulation, Numerical

More Olusegun D. Samuel's questions See All
Can inferior properties of crude biomass pyrolytic oil be attributed to the presence of polar compound?

Can basic inferior fuel related properties of crude biomass pyrolysis oil (BPO) be attributed to the presence of polar compound such as various oxygenates, nitrogen heterocycles and...

08 September 2019 4,766 4 View

What is the significance of additive in Oil Sands Recovery Processes?

What is the significance of additive in Oil Sands Recovery Processes? What is the role of Mechanical Engineer with the adoption of additive for recovery?

07 August 2019 6,559 3 View

How feasible is it to demonstrate solid fuel conversion and biodiesel modelling in program environments such as matlab, python and fortran?

How feasible is it to demonstrate solid fuel conversion and biodiesel production modelling in program environments such as matlab, python and fortran?

05 June 2019 4,547 4 View

What are the latest innovations in biodiesel production, hydrogen and fuel cells?

What are the latest innovations in biodiesel production, hydrogen and fuel cells?

03 April 2019 4,905 3 View

What are the useful material and book for modeling biomass conversion processes using relevant tools (e.g., Aspen Plus)?

What are the useful material and book for modeling biomass conversion processes using relevant tools (e.g., Aspen Plus)?

02 March 2019 7,865 3 View

As a Ph.D supervisor, how will guide your project students to investigate techo-economic study of CO2 capture in manufacturing industry?

As a Ph.D Supervisor, how will guide your project students to investigate CO2 capture and utilization in manufacturing industry via techno-economic tool?

01 February 2019 8,179 1 View

How can I adopt CFD, C++ and finite element to improve and model Li batery management for effective utilization?

How can I adopt CFD, C+ + and finite element to improve and model Li battery management for effective utilization? I would appreciate discussions on the technique of model tools, experimental...

01 February 2019 5,816 2 View

How will I develop and validate gas turbine combustors with Computational Fluid Dynamics (CFD) models?

Dear RG, How will I develop and validate gas turbine combustors with Computational Fluid Dynamics (CFD) models? Best Regards, Dr. O.D. SAMUEL

11 December 2018 1,853 4 View

Can cetane number of ethylic biodiesel production from oil (e.g coconut ethyl ester) be calculated from individual ethyl estters from a literature?

Dear RG, Literature has showed that cetane number (CN) of biodiesel e.g jatroha oil methyl can be calculated by CN =Xme (wt.%)XCNme; where CN is the cetane number of the biodiesel; Xme is the...

11 December 2018 8,575 5 View

What is the best way to teach CFD to undergraduate students in Department of Mechanical Engineering?

What is the best way to teach CFD/suitable lecture material to undergraduate students in Department of Mechanical Engineering?

11 December 2018 3,028 14 View

Similar questions and discussions
Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

Fabrication of narrow glass capillary (inner diameter 200~500 nm)?

I need a very narrow glass capillary for my research. How can I make a glass capillary with an inner diameter of around 200 to 500 nanometers?

08 August 2024 8,915 0 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to heat polymer for about 130° without oil bath ?

is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it

06 August 2024 947 1 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

How to start a Molecular Dynamics Simulation?

Is it possible to conduct a molecular dynamics simulation to see the effects of a specific carbohydrate on the structure of lipids (e.g., micelle structure)? I am a beginner in this field and plan...

03 August 2024 3,371 3 View

Do you think can be any gas and oil bearing rocks in Eastern part of Iran?

I want to know more about petroleum deposits in Iran.

02 August 2024 8,725 3 View

Which will be the best software for the Hydration shell analysis with molecular dynamics?

I am using a windows system, what software I should use for hydration shell analysis with molecular dynamics?

02 August 2024 3,143 4 View

Can we patent a process flow diagram developed using a process simulator but no actual cases is carried out?

Can we patent a process flow diagram developed using a process simulator but no actual cases is carried out? For example consider a process for certain product manufacture where a new process flow...

31 July 2024 781 1 View

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

29 July 2024 7,714 4 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close