Can laser cladding be done on curved surfaces?

P. Harihara Sakthi Sudhan @P-Harihara-Sakthi-Sudhan

31 August 2022 1 5K Report

pls do answer the possibility as per the state of the art current technology

Zahra Davariaraghizadeh

My specialty is fabric art and I sew by hand and I don't know about laser technology

Badges
Science topic

Similar topics
Mathematical Sciences
Graphs

More P. Harihara Sakthi Sudhan's questions See All

How to heat polymer for about 130° without oil bath ?

is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it

06 August 2024 947 1 View

Ti6Al4V - Phase differentiation between alpha and alpha prime martensite?

Dear Researchers, Is it feasible to distinguish between alpha and alpha prime martensite in the Ti6Al4V alloy under rapid solidification in the as-cast state using XRD, in addition to...

30 July 2024 3,849 0 View

How to interpret results of AST for Pseudomonas aeruginosa?

While doing AST for Pseudomonas aeruginosa, after incubation, no zone of inhibition observed in the plate near the well. wells surrounded by bacterial growth, when the same plate observed under UV...

25 July 2024 9,229 1 View

What is the Principle of Cysteine-carbazole-sulfuric acid reaction with glucose?

I have been looking for the principle of Cysteine-carbazole-sulfuric acid reaction in research papers and books, but couldn't find it. This reaction is mainly used for the quantification of...

23 July 2024 3,891 0 View

How can AI technology to enhance the agricultural productivity?

Farmers no longer have to apply water, fertilizers, and pesticides uniformly across entire fields. Instead, they can use the minimum quantities required and target very specific areas, or even...

22 July 2024 8,296 3 View

Can a paper that is posted as a preprint in a database with DOI, can be reviewed in another journal and accepted for publication??

It happened that I am asked to review a paper for a journal. Incidentally, the paper is posted as a preprint in another database as open access with DOI. It is completely citable. Now, should I...

17 July 2024 1,831 4 View

Do software tools exist to assess the economic and technical practicality of introducing new food products, such as yogurt with modified starch?

This question explores the world of food innovation and asks if there are computer programs that can analyze the financial and technical feasibility of introducing new food products. For instance,...

13 July 2024 7,446 0 View

How can I verify if an academic journal is a legitimate publication or a cloned version?

This question seeks to address the growing concern of cloned academic journals, which are fraudulent duplicates of legitimate publications. It aims to guide researchers, scholars, and academics on...

10 July 2024 5,966 2 View

Suggest a journal (Hybrid journal) which accepts short communications (Around 4 pages) and short reviews (Around 10 pages)?

In the area of material science and manufacturing engineering.

08 July 2024 5,576 0 View

To what extent Google Scholars Citations system is reliable?

1. I was shocked to discover yesterday that my research citations on Google Scholar had dropped to 2383 from 2419 a week ago, and they are now up to 2391. 2. My citations three months ago were...

28 June 2024 2,846 2 View

Using OBD technique i am trying to measure laser induced shockwaves velocity i found that at start velocity increases and then decay?

i am unable to interpret why its increases in start as shown in figure

11 August 2024 2,179 1 View

Hello researchers Is this a random laser or just fluorescence?

I am using Rhodamine6G as gain medium and silver nanoparticles as scatterers on a microscope slide and laser input 532 nm comes from above.

09 August 2024 9,894 2 View

Could dyes amplify the spectrum of light to a specific wavelength?

I am interested to know the behavior of dyes toward light. Specifically, Blue dyes re-emit the spectrum, especially from the green zone (known as principal in LED lamps, and blue dyes are known...

05 August 2024 3,290 1 View

How should operational parameters be selected when developing a pore-free laser welding technology?

There are three operating parameters - the laser power, the diameter of the focus spot and the scanning speed. It is necessary to obtain a seam of a given depth without pores. What parameter...

27 July 2024 7,168 2 View

Can we fit a gaussian Fit on a LIBS Peak ?

Though much literature suggests fitting a Voigt profile on a LIBS peak, is it also possible to fit a Gaussian profile on the LIBS peak? I have 204 spectra files, and I am building a pipeline for...

23 July 2024 6,127 1 View

How to download free version of BiofilmQ ?

I would like to use biofilmQ to analyse confocal laser image, how can do?

16 July 2024 7,628 2 View

How to install Quantum Espresso with Intel compiler ?

Hello ! I would like to do band structure calculations of perovsikites materials with quantum espresso. For this I installed the Intel Fortran compiler. This is what I get when I run the...

08 July 2024 1,207 0 View

How to add a mass source term in the continuity equation?

Hi, I am trying to model laser cladding in Ansys FLUENT. There are two phase: one is base metal surrounded by an inert gas (shown in the image). I want to add a cladding layer of the same metal....

07 July 2024 1,182 8 View

What is the best software for simulation of mode locked diode laser?

Hi Dear All I would like to simulate a mode locked semiconductor laser. Does anyone know what is the best software to do it?

06 July 2024 1,648 4 View

How to solve Bubble Error in fiber splicing?

I'm having a bubbling error while splicing 100/350 um optical fiber (core/cladding) on the Fujikura FSM100P+. I have tried some ways such as changing Prefuse power and Prefuse time but to no...

03 July 2024 7,463 6 View