How to interpret the CV curve of cathode for Li-ion battery?

05 June 2016 7,239 3 View

Could anyone provide me some informations about Lithium Copper Phosphate (LiCuPO4)?

04 May 2016 5,152 3 View

Can anyone give me some informations about the cyclic voltammetry of LiPF6 electrolyte?

Dear colleagues, I'm currently doing a research about Li-ion battery. In this case, I used LiFePO4 as a cathode. I got a peak of reduction around 0.8 V. I supposed that the cathodic peak seen...

04 May 2015 4,837 1 View

What is the indication of the absence of peaks in Methanol electrooxidation CV curves ?

I have several question regarding the MOR; hope anyone help me better understand. 1- in CV using (KOH+MEOH) what is the indication of absence of the redox peaks? shouldn't they exist as a sign...

28 February 2021 4,851 8 View

How to size battery banks?

I am designing a small grid connected solar PV power-plant. As the battery's capacity is specified in Ah and demand in kWh. What is the best way to size the battery bank? I have battery price in...

28 February 2021 1,638 3 View

How to model the battery pack in PSIM or PSCAD?

Hello, I have simulated a single battery cell using Thevenin equivalent circuit. For a battery pack, I have a large number of cells connected in series and parallel connections. Is there any way...

28 February 2021 2,116 1 View

How to calculate battery consumption for IoT device?

Hi, everyone I'm working on a privacy-preserving algorithm that will apply to IoT devices. So, I need to measure the power consumption by implementing this algorithm. Any suggestion, advice,...

25 February 2021 8,749 6 View

How the Ground Plane implantation is performed without damaging (and w/o varying the undoped nature) the top Si (8-10 nm) in FDSOI technology ?

It is a general practice to introduce Ground Plane in FDSOI devices under the BoX. The Ground Planes are introduced by Ion Implantation through Top Si layer and Buried Oxide. I wanted to know that...

24 February 2021 5,974 4 View

How to delaminate copper in water-based anodes?

Hello everyone, I'm looking for a way to delaminate copper current collector of water-based anodes in Li-ion batteries without damaging the graphite film. I tried different materials such as HNO3...

24 February 2021 3,785 3 View

Have anyone checked before Cyclic voltammograms of intial ITO substrate and E-teck?

As a beginner in electrochemistry, I tried to obtain cyclic voltamograms of commercial anatase powder deposited on an ITO substrate or on Eteck. After several attempts, I noticed that my cyclic...

23 February 2021 3,175 3 View

How to dissolve cross-linked Amberlite IRC120 H, hydrogen form resin?

Hello all, I have used Amberlite IRC120 H, hydrogen form acidic cation-exchange resin for the ion-exchange of waterglass [sodium silicate solution -- 40% Sodium silicate (mol ratio > 3.2)...

21 February 2021 5,614 3 View

What is the difference between AC conductivity and DC conductivity? Is AC conductivity = ionic and DC conductivity = electronic?

I am reading papers on batteries and although mostly people have reported ionic conductivity in Scm-1 but some have reported DC conductivity as well I and am confused as to what that is. Any help...

21 February 2021 9,207 6 View

How to prepare electrolyte of NaClO4 salt for Na-ion battery? Any problem with this salt?

Hello, I am trying to make anode for Na-ion batteries. I have no experience with preparation of the electrolyte for any batteries. NaClO4 salt are available and I am planning to use EC:PC as...

21 February 2021 8,132 1 View