Can I know how to apply contourlet transform for signals in MATLAB?Must I first convert 1D signal to 2D image in order to do this method?

Anyone plz suggest relevant topic for research in image processing+Deep learning.?

I have selected brain tumor images ...but now found that already lots of research done n this topic.

03 March 2021 5,774 3 View

Can we block unwanted images during the x-ray prediction?

i am try to classify the x-ray images. During classification , can i block unwanted images (except x-ray image).

03 March 2021 7,100 1 View

I need to image mesoporous silica nanoparticles that are in ~100 nm size and do high resolution TEM to look at mesopores. what grids should I use?

Need to image mesoporous silica nanoparticles using the TEM. Also, need high resolution TEM images to see the mesoporous structure. Kindly suggest what kind of grids to use. Thanks, Shatadru

02 March 2021 1,787 2 View

Do I need to strip the PVDF membrane before staining it with colloidal gold?

Dear Colleagues, After running Western blot on PVDF membrane and detection using ECL, I would like to stain my PVDF with colloidal gold to be able to allign the ECL image with total proteins on...

02 March 2021 7,829 3 View

Do you know any MR image dataset?

I would like to research on MR images (0.5T and 3T). Can you please suggest some websites that I can download dataset including both 0.5T and 3T MR images? Thank you.

02 March 2021 7,735 3 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

How to find the mode of classified ocean colour images?

Hello, I have classified 10 S3 OLCI images from the same area (althouth not the same size and/or quadrant) and I would like to do a final image using the mode of the pixel of these 10 images. I...

01 March 2021 9,874 3 View

How to perform statistical analysis of coefficients extracted from transform techniques?

I am studying the potential of DCT and FFT coefficients extracted from a signal to classify the different objects that emit the signal. I applied the Shapiro-Wilk to confirm that data was not...

01 March 2021 8,079 2 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

How to prevent ANFIS Model from negative prediction values in MATLAB?

I have input and output data set for "ANFIS modeling in MATLAB", and I am getting some negative predicted values of output in testing. However, the predicted values of output in training are...

28 February 2021 3,459 3 View

Muhammad Danish Ali

please give some more information on the issue .

one can start here:

https://www.mathworks.com/matlabcentral/answers/299772-wavelet-based-contourlet-transform

https://www.mathworks.com/matlabcentral/fileexchange/8837-contourlet-toolbox

Mahmoud Khaled Abd-Ellah

It depends on the data you have. You can use 1D or 2D to refer to your Dataset.

You can see this:

https://www.mathworks.com/matlabcentral/fileexchange/35322-hidden-markov-modelling-of-contourlet-transforms-for-art-authentication?s_tid=srchtitle

https://www.mathworks.com/matlabcentral/fileexchange/8837-contourlet-toolbox?s_tid=srchtitle