Can anyone tell how to simulate ferroelectric properties using VASP?

21 August 2020 0 2K Report

Hello,I have just started learning simulations using VASP.But as a newbie, I am having trouble to find out the simulation process for finding out ferroelectric properties(ferroelectric polarization).So if anyone kindly shows me the way,it would be very much appreciable.

Badges
Science topic

More Shahran Ahmed Joy's questions See All

How to estimate 2SLS with different instruments for different endogenous variables?

To be specific, I want to conduct an IV regression in stata with the following three equations. EQ1: Y1 ~Y2 Y3 X EQ2: Y2 ~ Z1 EQ3: Y3 ~ Z2 Both Y2 and Y3 are endogenous. However, Z1 and Z2 are...

23 February 2021 6,266 3 View

Hi, Good day! Do you have related studies about my title, "Factors Affecting the Senior High School Students' Stress Tolerance in Problem Solving"?

I am new researcher. I want to learn more and I need your help. Thank you.

04 February 2021 6,834 4 View

How to design a PI controller for fourth-order transfer-function ?

Hey! I'm in the work of designing a controller for a zeta converter, it is a fourth-order system. I tried ways like the Ziegler-Nicols method, Root locus method using Control System Designer in...

29 October 2020 4,054 3 View

How to cite the results from Gallup Strengths Finder Assessment?

In my report, I included the ideas from the results given to me by the Gallup Assessment, but I am confused on how I will cite the website using APA 6th edition and what is the format for both the...

12 October 2020 5,396 2 View

Is it possible to get more than one final optimal solution using TOPSIS decision-making method in multi-objective optimization problem?

So is it possible to get more than one final optimal solution using TOPSIS decision-making method in multi-objective optimization problem? If there is the possibility of getting more then one...

01 September 2020 7,680 9 View

How are latent means and observed composite means different?

I know that they are different but I am kind of at a loss for how to explain the difference, but I may be overthinking it. In simple terms, my understanding is that a latent mean(intercept) is an...

19 August 2020 8,857 4 View

How to model water acidification using CO2 and acids ?

Hello, I am trying to model the amount of CO2 vs mineral acid (HCl, H2SO4) needed to acidify water with various alkalinity conditions. It would be helpful if I can get some suggestions on the...

04 May 2020 9,798 8 View

How to calculate V0 (initial velocity) for a discontinuous enzymeaic assay?

Usually, for fixed-time or discontinuous enzyme assay, a specific incubation period (say 30 minutes incubation period) is required before the reaction is stopped and measured (say...

30 April 2020 2,506 2 View

Does Actively Growing Culture delivery from DSMZ require dry ice shipping?

I tried to see the details of the delivery of a bacteria in risk group 1. But couldn't find the exact information . https://www.dsmz.de/collection/catalogue/microorganisms/prices Does...

26 April 2020 7,021 1 View

How to do a two-way ONOVA in SPSS?

I don't have advanced knowledge of SPSS and tutorials aren't making much sense to me, if anyone is able to explain SPSS two-way ONOVA step-by-step in the simplest form I would be grateful. My...

30 March 2020 8,769 2 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

How to improve and implement WBAN MAC and Radio modules under Castalia 3.2 ?

Hello researchers, Hello Castalia3.2 researchers I am a beginner with Castalia, I work on optimization of RFID systems used in wireless body networks. I simulated a WBAN with 10 nodes and one...

28 February 2021 400 1 View

D2D implementation in Matlab in Vienna LTE software?

Hi Hope you are well. Can you please share your code for D2D implementation in Matlab. I want to implement D2D in Matlab based Vienna simulator and struggling to deploy D2D. Thanks

24 February 2021 9,378 3 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View

Is it possible to set a breakpoint at a specific DYNAMIC instruction using the GNU Debugger (GDB)?

Using GDB, it is straightforward to debug and monitor a target program by setting a break-point at a specific instruction, since the instruction addresses are known. However, we have two...

24 February 2021 1,598 2 View

Langevin Dynamics in shear flow?

Hi, We are trying to simulate particles with Langevin dynamics in a shear flow by Lees-Edwards boundary conditions in MD simulations. It seems thermal forces and shear flow do not go hand in...

23 February 2021 1,761 1 View

Should I use Pressure Based Solver or a Density-Based Solver?

Dear researchers, I want to simulate a flow (air) in a wind tunnel, and I want to integrate a fluidic actuator inside it in order to control the separation of the boundary layer. At the blower...

22 February 2021 4,882 3 View

How to simulate 5G Quality of Service characteristics?

For my research, I would like to simulate an end to end 5G network. My goal is to observe the behaviour of SDAP protocol, dynamic configuration of 5QI values etc. To summarize I would like to...

21 February 2021 7,624 3 View

Open Source IoT Simulators supported by Machine Learning?

Dear Research Gaters, Let me first add context to the question. I am looking to simulate the waste management system and resources of a city. The hardware devices I need to simulate include,...

21 February 2021 2,333 4 View

How can I simulate the optical absorption spectrum of a biomaterial (like DNA or protein) in COMSOL?

I need to simulate the optical properties of a biomaterial, namely DNA, in COMSOL. Basically I need to simulate the IR absorption spectrum of a cylinder filled with a 'concentration' of DNA. I am...

21 February 2021 3,043 3 View