How we control humidity in gas sensor?

Is humidity introduce when Ar/N2 is used as carrier gas in gas sensor?

05 June 2017 9,630 0 View

Please suggest me supplier or labs where i get CNTs/Si junctions based substrate?

02 March 2017 4,466 0 View

Can anyone guide me about air brush technique to deposit the film of CNTs?

Which type of gun/air brush required for this?

09 October 2016 4,877 5 View

Can anyone tell me, which solvent is required for CNTs thin film deposition by spin coater?

Generally, CNTs has poor adhesion on Si wafer, when deposit their thin filmby spin coater. So, I need a solvent that help in good adhesion of CNTs by spin coater...

09 October 2016 6,297 7 View

Can anyone suggest me, order of defect density in case of Graphene using Raman Spectrum?

In my case it comes 5e19cm-2... its very large as compared to reported values....

08 September 2016 4,531 0 View

Can anyone suggest me, how we calculate electrical band gap of CNTs?

Any appropriate technique specially for MWCNTs?

07 August 2016 2,499 2 View

Can anyone suggest me approximately value of electrical current in CNT/Pani Compoites?

with concentration of CNTs in polymer?

07 August 2016 9,405 3 View

Can any one suggest me, which type of sensors used to detect amount of, Chlorine, chloramine, Pb, VOC in water?

05 June 2016 2,330 2 View

Can any tell me, why resistance decrease as temperatures increase in case of MWCNTs?

generally, MWCNTs behave as semiconductor at room temperature.. in my case at room temperature, its i-v is perfect ohmic, but when we record i-v with temperatures.. i found that its resistance is...

04 May 2016 4,421 9 View

Can any one tell me, why electrical current is improved by the addition of CNTs in polymer matrix?

04 May 2016 9,886 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Sample dilution for quantitative analysis using ELISA?

If the detection range is in ng/ml but the reference range is in ug/ml for a molecule or protein in serum or plasma .how to dilute and what is the initial volume to be taken for quantitative analysis

02 March 2021 7,670 3 View

How to check the uv-vis absorption of nanoparticle by surface plasmon resonance?

I try to check the uv-vis absorption of Indium nanoparticle. Now I am measuring in solution, can I measure it in the form of a film?

01 March 2021 930 3 View

Any research papers for extraction of nutrient deprivation on macroalgae? Analysed by HPLC-UV and GC/MS. Possibly from macroalgae genus Rhizoclonium?

I am doing my thesis on the nutrient deprivation on the macroalgae Rhizoclonium sp. I will be analysing the levels over a period of roughly 5 days by HPLC-UV and GC/MS. I will be using seawater as...

28 February 2021 6,477 1 View

Necessary tube lenght to cool Natural gas in a dry-ice cooling bath?

I have a tank which contains natural gas at 250 Bar and 293 Kelvin. I want to cool the gas in a dry-ice cooling bath to about 195 Kelvin. The gas will flow in a copper-tube through the bath with a...

27 February 2021 8,128 1 View