Can accelerometer based wearable motion sensors be used to detect motion of fingers or a flex sensor is best suited for this?

I want to detect relative movement between fingers with wearable sensors. Which could be an appropriate technology for this?

31 December 2018 2,443 3 View

Can someone suggest me good book dealing with simulation of optoelectronic devices?

I am looking for a book to learn simulation of mostly semiconductor optoelectronic devices.

09 October 2018 351 0 View

What are practically achievable range and data rate for LoRa, SigFox and other IoT technologies?

If anyone has tested these IoT technologies in outdoor environment, could you please help me with max range and data rate that is actually achievable? I feel there is lot of difference between...

04 May 2018 1,299 0 View

What is the most suitable transceiver module for line of sight wireless transmission in 10 kms range?

I want a wireless transceiver module for remote sensing application with range about 10km. Xbee would not be sufficient. Can anyone suggest an alternative?

03 April 2018 5,651 10 View

Could anyone suggest some good journal to submit a purely theoretical work on semiconductor optics?

My work is related to theoretical modeling of a phenomenon in semiconductor lasers and I want to submit it in a reputed journal. Most journals in optics and photonics require experimental work....

02 March 2016 1,335 5 View

What is the physical significance of 'k' in a E-k diagram of a semiconductor?

What does 'k' refers to in a E-k diagram ? Is it a wavevector or something else?

01 February 2016 702 10 View

Is there any way other than "fft" to find the frequency content of a signal in Matlab?

I have complex values of a periodic signal which is clearly visible in time domain. But I want to find its frequency content ? FFT is not working with me and I am looking for alternate ways to...

11 December 2015 9,192 20 View

How can the random noise sources like Angle Random Walk in a semiconductor gyroscope be theoretically calculated?

Is it possible to theoretically predict the magnitude of random errors in semiconductor ring laser gyros?

08 September 2015 6,951 0 View

Can someone suggest me a good tool for simulating Semiconductor Ring Lasers?

I want to simulate both integrated and bulk fiber-optic semiconductor ring laser. Which of the tools e.g. Lumerical, Comsol, OptiFDTD will be most useful to me?

08 September 2015 4,701 1 View

What is the beam area of a laser wave and how to calculate it?

How do I find out the beam area of a light wave?

05 June 2015 2,785 0 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View