Can anyone suggest me a way to start simulating Hybrid plasmonic waveguides and calculate their transmission and other parameters in Lumerical?

Milad Taleb Hesami Azar @Milad-Taleb-Hesami-Azar

04 January 2016 1 3K Report

I want to start researching on plasmonic hybrid waveguides and need a tutorial to understand and simulate them in a suitable software?

Nicola Andriolli

Lumerical offers a tutorial introducing plasmonic simulations (login required). For more information I would suggest to look into the Knowledge Base or inquire in the Knowledge Exchange (login required, as well).

Badges
Science topic

Similar topics
Engineering
Modeling

More Milad Taleb Hesami Azar's questions See All

I want to performe MALDI-TOF MS for bacterial identification, I would appreciate it if anyone can tell me the matrix solution preparation protocol ?

based on what I've studied on multiple papers, for peptide and protein identification Alpha-cyano-4-hydroxycinnamic acid (CHCA) is an appropriate matrix to use, I also know that the CHCA powder...

26 February 2021 6,799 3 View

How to achieve the sensitivity diagram of a sensor in CST?

I wanna design a sensor in CST 2021 for the first time and I don't know how to achieve the sensitivity diagram of the sensor in CST. Could you plz help me to do that? I appreciate your response...

26 January 2021 6,864 1 View

What kinds of potential genes could be expressed in frogs exposed to chytrid fungus in different environmental conditions ?

I need an applicable molecular biomarker like expressing the genes in frogs who expose to chytrid fungus in different environmental stressors. Indeed, what kinds of genes I should notice in frog's...

25 January 2021 7,718 2 View

How to select the most non-correlated samples within a dateset?

Dear researchers How to select the most non-correlated samples within a dateset? Considering that the samples are time-series of length l within m different time-series. To more clarify the...

13 January 2021 741 6 View

DSC test- Glass transition temperature of the electrospun PA66 nanofibers?

Hello Everyone, I did several DSC tests on the electrospun PA66 nanofibers to obtain the glass transition temperature. According to the material datasheet, the Tg point of PA66, as cast, is around...

13 December 2020 1,506 2 View

How to create a sag and swell detection in the DVR applications?

I have created a three-phase cascaded h-bridge inverter at Simulink with the SHE-PWM technique, and I want to test it in the DVR applications. How can I design a controller for that in the DVR...

13 December 2020 735 3 View

Degenerated semiconductor (Burstein Moss effect) with unchanged band-gap?

Is it possible to produce a degenerate semiconductor using a dopant agent that results in increasing the electrical conductivity, but the optical band-gap remains unchanged? In such a situation...

11 December 2020 8,338 13 View

Which statistic software can give me a relationship for multivariate function?

Hi friend I have some data and they influence on each others and I draw their graph in excel but excel can't give me a relationship for multivariate function. the regression of these data in excel...

29 November 2020 9,371 9 View

A paper may be rejected because of several reasons?

In my case, I have received rejection after seven months from submission to journal without reason or editor comments (decline). Moreover, without being reviewed by an expert scientist reviewer,...

29 October 2020 5,437 4 View

Do scalar-tensor-vector gravity theories violate the Bekenstein-Hawking area law to compute the entropy of black holes?

I am looking for the thermodynamics of the cosmological black hole in scalar-tensor-vector gravity theories. I know how should I write and find the thermodynamical quantities and equations for...

26 September 2020 6,383 3 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein?

Hi In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein? I got this error in the add-ion stage: Fatal error "./ amber99sb-ildn-HHH.ff / force...

01 March 2021 8,747 4 View

How can you bring two structures together to create an adhesive bond in LAMMPS?

I have created an Ice 1h crystalline structure and an Aluminium substrate structure and equilibrated both at 250K. Now I need to bring them together in a way that an adhesive bond is created....

01 March 2021 3,325 2 View