Can anyone provide the stiffness and damping coefficient of multibody human model joints?

07 December 2013 1 9K Report

I obtained the equations of motion of human multibody dynamic model subjected to rear end impact and need to use the value of damping and stiffness of joints.

Hunor Erdelyi

Dear Aghil,

See the paper below, I think it will help you with your question:

Pier Paolo Valentini, Virtual dummy with spine model for automotive vibrational comfort analysis, Int. J. Vehicle Design, Vol. 51, Nos. 3/4, 2009.

Regars

Badges
Science topic

More Aghil Seydi's questions See All

Hi everyone I have a question regarding lentivirus concentration using concentration columns. Has anyone had any experience with this?

If we do not have access to an ultracentrifuge and PEG is lethal to our target cells and has a highly toxic effect, the articles mention the use of lentivirus concentration columns. Does anyone...

16 December 2023 8,999 0 View

Transmission of hepatitis during tooth filling?

How many percent of the disinfectants used in dentistry prevent the possibility of hepatitis transmission during tooth filling?

14 May 2023 9,781 2 View

Are RNase enzyme will be reactivate in the DEPC-treated water after autoclaving and DEPC inactivation?

I need RNase-free water to make an electroporation solution, however, I want to autoclave the solution for sterilization. Do you think the solution will contain the enzyme again after the...

28 June 2022 451 0 View

Can we use HPLC for measuring the amount of Bisphenol A (BPA) or disodium salt of BPA dissolved in DMSO?

I am doing a reaction between Bisphenol A (BPA) and NaOH to produce disodium salt of BPA. Firstly I use Dimethyl Sulfoxide (DMSO) as an organic solvent to dissolve the BPA and then add 50%...

31 January 2018 8,264 8 View

How can I find the time history of a wave?

How I can find "time history of wave" by 1 second step at least for 20 min?

22 November 2014 5,599 9 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

29 July 2024 7,714 4 View

May I know the exact Quartile of the journal- Advanced Engineering Materials (Wiley) for material science category?

In some data sources it has been grouped in Q1 and some shows it is Q2.

29 July 2024 4,227 2 View

Ternary in Electrical Engineering?

Dear Research Community I would like to invite Elctrical Engineering specialists to solve problems related to Ternary Algebra or tripple sets I have an algorithm that places in relation three...

28 July 2024 5,771 2 View

What topic or subject does Production Engineering need to address more?

Contemporary scores or innovations in scientific approaches. Hybrid methodologies, emerging themes and cross-cutting issues?

27 July 2024 648 3 View

Can you visualize platelets using EVOS ?

Hi all, My lab has Thermo Scientific™ Invitrogen™ EVOS™ FL Auto 2 Imaging System, and I was wondering if I will be able to use it with whole blood, whilst focusing on platelets? The idea would...

24 July 2024 9,337 3 View

Can a shoot-through event of a tri-state digital buffer cause momentary Hi-Z state?

// interested in the difference between floating events and short circuits.

22 July 2024 6,565 0 View

Is there a good macro photography kit for on-site metallurgical investigation?

I am looking to purchase a photography kit for onsite metallurgical investigations, such as capturing photos of worn areas, hot tears, cold tears etc. Could anyone suggest me a good...

22 July 2024 3,490 2 View

Why do fish have fishy odors naturally ?

Chemical Engineering /Food Engineering

20 July 2024 4,152 4 View

What could be the possible reason that sintering of polycrystalline diamond fabricated with tape casting has suddenly started failing?

I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...

16 July 2024 3,212 5 View