What am i doing for begining a render motor?

HELLO every one... I want to learning a render motor. what am i doing for beginning a render motor? an anyone help me?

04 May 2016 8,122 0 View

What are the requirement for employee in nvidia corporation?

Hello everyone ... what are the requirement for employee in nvidia corporation? experience and others...?

04 May 2016 5,362 0 View

How can i measure delay for packet received in RadioTest in Castalia?

I want to measure delay for packets and use it .

08 September 2014 4,251 0 View

WSN application

my thesis is about congestion control in WSN, buti want to use my protocol in a application, can you help me to definean application that my protocol is used

08 September 2014 992 3 View

How can I give matlab output (fuzzy logic file(.fis)) to castalia as an input?

How can I give matlab output (fuzzy logic file(.fis)) to castalia as an input?

08 September 2014 5,615 10 View

I have a .fis file in matlab (fuzzy rules). Can someone help me to convert it to a language that is understandable for omnet and castalia?

08 September 2014 7,746 3 View

Can anyone help me to create an application in castalia?

Can any one help me about create application in castalia that notes sense data and forwards them to sink to test some parameters like number of sensors and rate of sending? I don't know how to...

07 August 2014 4,939 1 View

Can anyone help me to measure consumed energy in matlab for Wireless sensor nodes?

07 August 2014 802 1 View

Why in castalia, with increment in transmission rate, the consumed energy in nodes(sink node) is decrease?

In radioTest simulation, the consumed energy is decreased with increase in date-rate? why?

07 August 2014 7,719 6 View

Why when I run a radio test, castalia's standard output file (100806-222319) doesn't get created?

When i run a radio test, castalia's standard output file(100806-222319) doesn't get create.please help me,thanks in advance

07 August 2014 3,184 5 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein?

Hi In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein? I got this error in the add-ion stage: Fatal error "./ amber99sb-ildn-HHH.ff / force...

01 March 2021 8,747 4 View