Can anyone help me to convert my .stl file to .stp file features of CATIA?

08 August 2015 0 6K Report

I have .STL type files which are supported by DEFORM-3D, but i want to use the same file in HYPERXTRUDE but it allows to support .STP fIles . I need conversion software or any methods to transform the files.

Badges
Science topic

More Deendayal Kumar's questions See All

Anyone there who can tell me about the best features and SHORTCOMING of QFORM extrusion software?

Please share your working experience with QFORM related to extrusion simulation

31 December 2015 8,746 0 View

Can we stop simulation and modify the input parameters and re-run the simulation in QFORM extrusion software?

Anyone working with QFORM software please guide me to re-run the simulation process after modifying the input parameters. or please suggest some alternate solution to continue with the simulation...

11 December 2015 2,608 2 View

Can anyone provide information on the rolling parameters associated with rolling of aluminum foils?

When we cold roll aluminum foil we are not able to control the speed of the rolling process. According to rolling theory the speed of the rolling process should be more when thickness is reduced...

31 December 2014 7,958 4 View

GC-MS retention index prediticon?

Hello experts, Does anyone know any free software about retention index prediction ?

08 August 2024 7,403 2 View

The question is how to use Wavenet transform?

HOW CAN I WRITE A CODE TO USE THE WAVENET TRANSFORM AS A FEATURE EXTRACTION METHOD INSTEAD OF DWT IN MATLAB?

03 August 2024 7,829 0 View

In WECS : Gain values for conversion of PMSM rotor speed(rad/s) to p.u. input to wind turbine and Torque(pu) of WT to input of PMSM-Torque (Nm) ?

I am working on developing a MATLAB Simulink model of Wind turbine with PMSG followed by MPPT Boost converter. I have gone through so many literature and videos but I am not finding clear solution...

03 August 2024 888 1 View

Can anyone provide me with molecular docking softwares/ websites?

Molecular docking software/ websites?

02 August 2024 8,704 7 View

Some new emerging problems on application of RL for scheduling in IoT networks?

I have seen plenty of existing works on applied Reinforcement Learning (RL) policies for optimized scheduling in IoT networks including Q-learning, DQNs, and the newer ones including PPO for...

01 August 2024 8,754 2 View

I am working on my Master's thesis on the biogeography of the genus Ruagea and I would like to ask, could someone help me to check whether my result?

I created a file with my outgroup and ingroup species using Beauti, ran it in BEAST, viewed it in Tracer, and then used TreeAnnotator to create a file that I imported into RASP. Could someone...

28 July 2024 2,979 1 View

How can one determine the conversion factor for a radiolabeled substrate to a radiolabeled product using slopes from linear regression equation?

I am preparing a radiolabeled product using a radiolabeled substrate. I have the cpm values for different dilutions of both my known substrate and unknown product ? How can one determine the...

27 July 2024 3,604 1 View

Which software tools are best for enhancing diagnostic accuracy in chest X-ray imaging using image reconstruction and neural networks?

I am reaching out to seek your valuable advice and recommendations regarding the best software tools to use for this research. Specifically, I am looking for software with a user-friendly...

22 July 2024 3,794 1 View

How to test multivariate outlier in STATA?

Hey all, I need help testing for multivariate outliers using STATA for my master thesis. The literature recommends the Minimum Covariance Determinant (MCD) (Verardi & Dehon, 2010). I found the...

22 July 2024 8,821 2 View

MDCI module in Orca software?

Dear Researchers, My question is associated with the "MDCI" method in Orca. Please let me clarify my question using a simple example: Suppose we are going to perform CBS extrapolation using "!...

21 July 2024 1,632 0 View