Simulation of two phase slug flow in inclined pipes using Fluent?

I am simulating slug flow in inclined pipe, so to avoid problems with geometry i have changed the gravitational vector into 2 components according to the angle of inclination. My question is, when...

01 February 2018 7,185 3 View

How to calculate Wake length and volume around bubble?

I am simulating single Taylor bubble rise in stagnant liquid using VOF method in ANSYS Fluent, i want to calculate the wake length and volume? Any suggestions please?

11 December 2016 270 4 View

How to Compile and Load UDF in FLUENT 64-bit on windows 8?

10 November 2016 8,178 6 View

How to plot Liquid film thickness and velocity in gas-liquid vertical slug flow?

04 May 2016 7,382 4 View

How to Investigate the effect of Dimensionless numbers on two phase flow in ANSYS fluent?

04 May 2016 2,268 5 View

What are the main considerations when calculating time step size for transirnt vof method in Ansys Fluent?

I am working on gas-liquid slug flow in vertical pipe, and changing pipe diameter is one of the parameters that i aim to investigate, so when changing diameter i need to update the time step size....

01 January 1970 709 6 View

Can linear DNA be used as template for site-directed mutagenesis?

Is it possible to induce site-directed substitution mutation by quick-change method on linear dsDNA? or it has to be cloned in some vector? If yes, should it be treated with the Dpn1 enzyme...

03 March 2021 401 4 View

PUC19 as a transfer plasmid for lentiviral delivery?

Hello, Is it possible to use pUC19 as a transfer vector to be packed in using the second generation viral particles packaging system( pMD2.G; psPAX2 plasmids)? As far as I understand it there is...

28 February 2021 4,868 2 View

Is the a way to contol flow (Flow velocity) without impacting pressure value?

I have a pipe with 10 mm in Diameter and 2 bar pressure, the fluid velocity is 200 m/s, the fluid is air. is there a way to reduce velocity without affecting the pressure value?

25 February 2021 7,187 3 View

Which software is best to analyse multi-phase fluid flows ?

Hello everyone, hope all is good. I want to analyse multi-phase fluid flow through pipe, which software is best to do so ?

21 February 2021 4,230 8 View

How to get the vector of a specific vibration mode in phonon dispersion?

For example, I have this phonon dispersion(Fig. 1), and now I would like get vector of atoms which describes TA1 in P. I know v_sim can show vibrational animation of specific mode, but I do not...

20 February 2021 4,332 4 View

Specify the Burgers vectors for dislocations, which cannot be uniquely identified.?

1. A bcc metal single crystal was sliced along (1 -1 0) plane for TEM study. Assuming that the TEM available is equipped with a goniometer stage which tilts up to 45o. The Burgers vector of...

20 February 2021 2,370 1 View

I am working on image transmission, i converted the image into binary vector, i want to extract the MSB of each pixel ?

i have a vector 1*512 size, i want to take the first value every 8 elements and put these elements at the end of the vector,how to do this on matlab ?

19 February 2021 2,352 5 View

Does the property of GFP affect a fusion protein's localization?

Hello, I am planning to insert GOI between CaMV 35 promoter and mGFP in pCambia1302 to produce a fusion protein and see subcellular localization of the protein. But the vector says it's membrane...

15 February 2021 4,353 3 View

How much amount of DNA (ligation mix) should I use for transformation?

Hi Fellow Scientists! I am trying to clone my 300 bp insert into a 6 kb vector. I run a few different ligation reactions using (1:3 vector: insert molar ratios) 10, 20,30, and 40 ng/ul vector...

15 February 2021 9,563 6 View

Can I express protein of plant origin in E. coli strain (M15) using pET28a vector systems? Are M15 strains and pET vector systems compatible?

Are E.coli strains M15 and pET28a vector systems compatible? Can I over-express my protein which is of plant origin. Previously I was using BL21 DE3 strains. Was confused to use M15 strains for...

10 February 2021 2,564 3 View