Is Mechanically Recovered Meat (MRM) fit for eating?
Mechanically deboned meat is - when properly prepared - as good as hand deboned meal. It all depends on the starting material and the procedures used.
See for some info
Article Cadmium and lead in muscle tissue and organs of broilers, tu...
Please provide few ways to interpret structural model.
11 December 2018 4,860 0 View
During my interaction with the young researcher (age less than 30), I found many of them are stressed and are not happy with their work/outcome of the work. Many of them are not able to state the...
06 July 2018 6,913 8 View
How many people are in the selection committee which decide that a journal should be indexed in Science Citation Index Expanded?
06 July 2018 8,582 4 View
People often compare two researchers outcome based on their research paper. Is it correct way of doing such comparison?
05 June 2018 8,273 5 View
In general, young researcher spent most of the time doing experiment or developing a research paper, I observed they are alienated from extra curricular activities. I also found that researcher...
05 June 2018 6,372 9 View
In today's world when unethical practices are spreading in all areas of life, How important is to check ethical practices followed while conducting a research?
07 August 2017 9,465 2 View
When a error is found in a peer reviewed published research, how to correct them?
07 August 2017 9,483 2 View
As a full time researcher needs to dedicate his most of the time towards his research, can someone suggest few ways to balance life between research and family.
07 August 2017 4,203 1 View
04 May 2017 2,821 0 View
With the aggressive advancement of technology, physical relationships with society are becoming weak day by day. I need few study which discussed the relevance of traditional Social Sciences today.
02 March 2017 6,787 0 View
02 March 2021 3,060 3 View
Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...
02 March 2021 4,910 3 View
Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...
02 March 2021 1,999 5 View
I think we were all surprised at the first time we got to know quantum mechanics that the squared modulus of the wave function is the probability density of the existence of the particle? The role...
28 February 2021 6,282 9 View
Hello, I have used the shell function on SpaceClaim to create thin solids for the model I am studying. These are contained within an enclosure for my study. I chose this approach as it avoids the...
24 February 2021 8,856 3 View
No streamlines present means whether the flow is getting obstructed there and the velocity inside the region is zero? Or else, the fluid is trapped inside that region with a nonzero velocity?...
22 February 2021 5,249 10 View
I'm trying to study cracked structures under a compressive load taking into account contact between the crack lips. I would like to know if the method of extrapolation by displacement remains...
21 February 2021 8,694 4 View
I have tried Idelchik's Handbook of Hydraulic Resistance 4th Edition (2007 page 300) formulas and across some range the formulas are reported valid for, the law of conservation of energy is...
20 February 2021 2,504 1 View
Hello All! I'm trying to model a contact between a coated substrate and a tip in Abaqus. The coating is ultra-thin compared to the geometry of the substrate. So I defined the coating using the...
16 February 2021 1,594 3 View
Hi everyone. I am looking for a high temperature MPCM. More specifically, I need the thermo physical properties of a microencapsulated phase change material with the melting temperature between...
14 February 2021 3,606 2 View