Can anybody refer to me some fast peer review journals in Power Electronics and Electrical Engineering fields?

Omid Alavi @Omid_Alavi2

01 January 2015 11 8K Report

ISI or non-ISI ( but valid )

Badges
Science topic

Similar topics
Academic Journals

More Omid Alavi's questions See All

Can you help me with modeling discrete variables in PSO algorithm?

Hi to all, My question mainly lies in the updating process of the elements that determine the location of the DG units in planning problem. You can find more detailed explanations about my...

07 August 2016 4,348 3 View

What is the problem with "Static Code Metrics Report" error in Matlab?

Hi to all,I've got the error of "Static code metrics report was not successfully generated because of the following errors" when I try to deploy a Matlab Simulink model to the hardware (the...

04 May 2016 7,523 1 View

How can I draw a map with highlighted regions?

Dear Researchers,I want to make a heat map for about 160 points (Lat,Long).I have Lat and Long for these 160 points, and each point has a specified value.I searched a lot but I could not found any...

02 March 2016 456 5 View

Is my full-bridge boost converter simulation correct?

31 December 2014 8,903 7 View

What is a typical value for grid's inductor in MATLAB simulation?

What is a typical value for grid's inductor in MATLAB simulation? I want to know value of the equivalent load for H-Bridge of inverter that it is shown in Figure. With assume that it is connected...

31 December 2014 7,057 6 View

Is "International Journal of Scientific and Engineering Research ISSN: 2229-5518" a valid Journal ?

Is "International Journal of Scientific and Engineering Research ISSN: 2229-5518" a valid Journal ? I checked this journal in researchgate impact factor and it is 3.2,but this journal is not index...

31 December 2014 1,883 57 View

Can anybody refer to me some valid journals for Applied Physics-Optic with fast peer review?

Can anybody refer to me some valid journals for Optics-Physics with fast peer review? ISI or non-ISI

31 December 2014 9,043 6 View

How can I simulate optical current transformer (OCT) with matlab simulink?

How can i simulate OCT with matlab simulink?

31 December 2014 5,326 2 View

How can I solve this problem in my inverter?

I simulated a 7-level grid connected inverter using Matlab.When I changed my load from R to RL, I saw a spike in 0-1 level, I think this problem is related to reactive power,How can I solve this...

31 December 2014 3,363 6 View

What is the typical photovoltaic panel model using matlab simulink?

31 December 2014 1,944 2 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

Irradiation data for JAPAN?

Hi, Could you help me to get the latest (2019, 2020) solar resource data for a particular site in JAPAN? PV GIS and NSRDB data are not in reach to JAPAN, I'm looking for some other database for...

03 March 2021 961 3 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View