Can anybody give me information on resistance/sensitivity to heat of aflatoxins and those producing agent, Aspergillus sp?

More Namdar Moradi's questions See All

How can I magnify an image without changing the dimension in matlab?

Hi everyone. For the last part of my project I have to see how does my program respond to a magnified image. The magnification has to be a part of the code . I've tried imresize() , it will be...

10 February 2021 8,279 10 View

How can I remove bubble in WPU film?

I am trying to prepare water-based polyurethane films. When dried air bubbles were formed and destroys the film homogeneity, then I can't use this for mechanical test because of defects. Is there...

26 January 2021 701 1 View

What is the best way to simulate the fractional controllers?

What software do you prefer?

29 December 2020 889 3 View

How can I omit some special part of an image in matlab?

Hi I'm trying to edit my input image which is a simple Persian letter. I want to omit the dots of the letter. I can do it with Photoshop of course, but it would be more technical if I could do it...

14 December 2020 201 5 View

How can we choose the right method for Gaussian calculations?

I'm not working on biomolecules, I work on Organic, Organometallic, and sometimes inorganic structures. Do you know a simple way to apply the right calculation method? Is there any article or...

10 December 2020 3,396 5 View

How can I estimate meniscus force on a needle in FLUENT??

I want to simulate a needle movement in water and I want to know how can I estimate meniscus force on the needle in FLUENT.

06 December 2020 9,766 1 View

How can I design Vanderlugt filter in Matlab?

Hi everyone I need some help in designing Vanderlugt filter in Matlab. I want to design this filter and later use it in a 4f optical correlator. As I tested my designed filter and I'm not sure...

19 September 2020 8,662 7 View

How can I calculate leakage flow rate of gas by using gas concentration at two or more positions in air?

Suppose there is a leak in gas pipeline. I just have a sensor to measure concentration of gas in air. Can I calculate leakage flow rate of gas by using gas concentration at two or more positions?

04 August 2020 5,354 3 View

Is it possible to accidentally move multiple robots at the same time to reach a specific destination on MATLAB software ?

I wrote a code on matlab and the goal is to make the robot move randomly and reach the destination. How to convert this code into multiple robots that move randomly and reach a specific...

27 March 2020 9,300 4 View

Does the "Schumann Resonance" has any effect on the enhancement or reduction of human brain waves "Especially the alpha wave"?

Is there any article or project about interaction of the "Schumann Resonance" on the brain alpha or theta waves? The Schumann resonances (SR) are a set of spectrum peaks in the extremely low...

02 March 2020 3,146 2 View

How does the gut microbiome affect the fibrotic process within the liver?

and Can the gut microbe be used for the treatment or diagnosis of liver fibrosis?

02 March 2021 557 2 View

How to remove the residual PDMS on the silicon mold?

Incompletely cross-linked pdms are difficult to remove.

01 March 2021 798 3 View

The reason that the culture of white fungi Contamination with green mold(Trichoderma), the culture autoclave at121 for 15 min. What is it?

Is the period to autoclave not enough? The inoculation in a hood and flame and UV and alcohol.

27 February 2021 9,356 3 View

How to indicate the degree of litter decomposed by microbes?

Any technique could detect the degree of litter decomposed by microbes? Or any indexes could do this job? I want to split the contribution of microbes during decomposition, so any suggestions...

23 February 2021 1,362 5 View

What kind of steel moulds are used for hot pressing metal powders?

My main concern is that the metal powders should not weld to the mold surface and I should easily be able to eject out the pressed samples. I am looking for alternative for graphite moulds. The...

22 February 2021 2,965 4 View

How can we add reinforced thermoplastics with granules in injection molding machine?

I need to make an injection molding machine in which short fibers are to be introduced. Short fiber length and material properties are to be determined and also the material strength are to be...

22 February 2021 4,290 1 View

Can I get information about research laboratories that are currently having in culture, internationally/locally standardised microorganisms?

Microorganisms of interest include; E.coli; Salmonella typhimurium; Pseudomonas aeroginosa; Streptoccocus pneumoniae; Staphyloccocus aureus and Candida albicans. Locations closer to Port...

18 February 2021 6,500 3 View

How do microbes tell the presence of an inorganic minaral in the soil?

Due to their ubiquitous nature, there is a tendency of the presence of microbes in a given mineral(s). For instance, if microorganisms that love the of pH less than 6 in the pH value, is isolated...

03 February 2021 4,630 10 View

Does the UV radiation affect on fruits ?

I want to examine a kind of fruit's extract's antimicrobial effects. At first I want to put it under the UV radiation to prevent the mold or any kind of fungi's and bacteria's growth. The...

24 January 2021 8,350 20 View

How to lessen cell growth?

I am working on the 4T1 murine breast cancer cell line. from the first day I bought this cell line, the cell's growth rate is extremely high. I intend to make these cells resistant to a single...

24 January 2021 2,884 3 View