Can any one tell what is this error In AFORS HET 2.4.1 software ?

More Venkanna Kanneboina's questions See All

Can anyone suggest how to improve c-Si/a-Si:H solar cell efficiency?

I have fabricated Ag/p a-Si:H/i a-Si:H/p-c-Si/i a-Si:H/n a-Si:H/ITO/Ag solar cell by PECVD, i a-SI:H layer thickness iis about 5 nm, p,n a-Si:H thickness is about 10nm, ITO (by sputtering)is 80nm...

21 May 2016 2,989 13 View

Why does blocking with my immunogenic peptide cause nuclear fluorescence in ICC?

Hi all, I am validating a polyclonal antibody raised against human ANT4, through WB and ICC. In most of my controls, the antibody shows very little off-target binding, but when I pre-incubate the...

03 March 2021 5,999 3 View

Why can't make aluminum nitride film successfully by use sputter?

We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...

03 March 2021 7,975 3 View

Irradiation data for JAPAN?

Hi, Could you help me to get the latest (2019, 2020) solar resource data for a particular site in JAPAN? PV GIS and NSRDB data are not in reach to JAPAN, I'm looking for some other database for...

03 March 2021 961 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

12% ledeburitic cold work tool steel, etched for revealing retained austenite, any help for clarifying?

Hello everyone. Given microstructure image belongs to a 12% ledeburitic cold work tool steel (annealed and tempered). The sample was etched with picral (100 mL ethanol and 4 g picric acid). I...

02 March 2021 4,119 3 View

Does Napabucasin soluble in dichloromethane and in ethanol?

I need to prepare a solution of Napabucasin (inhibitor of cancer cell stemness) in dichloromethane. The drug is expensive, so maybe somebody already tried to do it. If it is soluble, what is the...

02 March 2021 9,945 3 View

Help request in CST microwave?

im working now on TPV solar cells and metamaterials and i realy need our help in CST microwave i have a tpv cell simulation and i want to extract particullarly the absorbtion of only the active...

02 March 2021 2,246 2 View

Anyone found any research papers on solar furnace design calculations (for solar concentration)?

I am thinking about working on solar furnace with heliostats that concentrate sunlight and heat molten salt, but currently no luck with research. Not a lot of papers based on the subject. (check...

01 March 2021 5,023 5 View

How to check the uv-vis absorption of nanoparticle by surface plasmon resonance?

I try to check the uv-vis absorption of Indium nanoparticle. Now I am measuring in solution, can I measure it in the form of a film?

01 March 2021 930 3 View

How to remove the residual PDMS on the silicon mold?

Incompletely cross-linked pdms are difficult to remove.

01 March 2021 798 3 View

Soumyadeep Misra

You could try to run the program as administrator. Let me know if it is helpful.

Venkanna Kanneboina

k. thank you sir

Shyam Trivedi

It's in German.. it means "access to a file is denied"..either run the program as administrator OR give full rights to the particular folder where read/write/save operation is taking place.

Ayodeji Awodugba

I have an issue with version 2.5 also. The external parameter window is not not activated. Can somebody help in this regard?

Kyaw Zin Phyo

I also occurred this error. How can run software AFORS HET 2.5 version?

Prashant Gautam

Always right-click the icon and open it in administrator mode. Then allow and click yes.