How to approach CFD simulation results of a flow past a cylinder?

Hi all, I'm doing a transient simulation of flow past a rectangular cylinder close to the free surface. As far as I'm concerned, the common practice is to discard the initial stages of the...

25 February 2021 1,348 3 View

How to calculate time-averaged fields from Ansys CFX solver?

I would appreciate any comments on the following problem. I need to calculate mean fields (e.g. pressure, velocity and vorticity), for which I activate Trn Stats tab in CFX-Pre. However, what I...

21 February 2021 8,548 7 View

The most suitable turbulent models to predict flow past a floating body?

Hi all, I'm planning to simulate flow past a floating body using CFD method with the main purpose of investigating its stability against hydrodynamic forces. A sketch of the problem is presented...

28 January 2021 5,872 5 View

Stable region for VL model?

29 December 2020 4,125 3 View

Can anybody suggest me a cheap material for surface modification of hydrophilic Titania nanoparticles?

I'm looking for a cheap material to modify Titania nanoparticles in order to use them in polymer and increase its contact angle.

13 December 2020 504 5 View

How can I fix the capacity curve of two different structure?

I have two frames for nonlinear analysis, one of them is CBFs and one of them is BRBFs ( the generals are the same, only lateral elements are different). When I drew the capacity curve of my...

11 November 2020 10,034 3 View

How to measure the equivalent sand-grain roughness of a sandpaper?

I want to use standard sandpapers of different grit sizes to impart flow resistance to a surface. I am wondering how to convert the roughness of sandpaper to an equivalent sand-grain roughness. Is...

18 October 2020 9,384 3 View

How to calculate transvers current correlation function (MD)?

12 October 2020 4,424 1 View

How can I obtain thermal efficiency in thermal photovoltaic (PVT) systems by CFD (FLUENT) method ?

Hi everyone I have a question about the thermal efficiency of photovoltaic thermal (PVT) system by CFD (FLUENT) method. Why thermal efficiency in the morning with 400 W/m2 radiation is more than...

13 September 2020 2,543 4 View

How to deal with ANSYS Q3D surface mesh generation error?

I am trying to extract the stray inductance of a PCB bus bar using ANSYS Q3D. I tried different types of meshes but every time in the middle of the simulation, this error "Surface Mesh Generation...

10 September 2020 2,060 3 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

How to compare two groups with only two measurements?

Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

03 March 2021 8,796 3 View

Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence?

I am on the lookout for the Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence. Does anyone know where I can find it? Thank you in advance

03 March 2021 3,568 1 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View