Calcium recovery in steel

Dr. Pallavi Deshmukh @Dr_Pallavi_Deshmukh

01 January 1970 1 4K Report

Dear All,

How the recovery of Ca in steel is related to the cleanliness of steel?

Higher is the % of formation of CaO, CaS, calcium aluminate in steel lower will be the recovery..then why steel industries are aiminig at higher Ca recovery %?

Dr. Pallavi Deshmukh

Is the Ca% in the slag is determined? if it is so then higher the Ca% in slag better is the performance of CaSi...please give your expert input

Badges
Science topic

More Dr. Pallavi Deshmukh's questions See All

What should be the free board, feeder (cored wire) station height, feeding rate for the set up of wire feeder for 400 kg capacity ladle?

To set up the trial for CaSi cored wire insertion to produce clean steel (400 kg capacity) for R&d purpose, how to decide the free board, feeder station height, feeding rate to get maximum...

06 July 2019 6,817 5 View

What is the relation between viscosity and volume occupied?

Is it possible that higher viscous material will occupy the higher volume or vise versa? Is there is any funda of capillary action, such as inter atomic force of attraction between particles and...

04 May 2019 465 4 View

How to differentiate between metallic and oxide Ca in CaSi (Calcium silicide) powder?

What are the characterization ways to differentiate between the metallic and oxide calcium in the calcium silicide powder?

04 May 2019 5,659 1 View

What is the purpose of keeping a gap between Ca rod and steel sheath in the cored wire?

It was observed that keeping a little gap between the Ca solid rod and steel sheath (CRCA steel strip) in the cored wire has a large impact on the Ca recovery% in the steel melting. May I know the...

01 February 2019 9,875 2 View

Dear all, what is the chemistry between calcined alumina (Al2O3) and PAF (potassium aluminium fluoride or potassium cryolite) in aluminium melt?

PAF forms a low melting phase with Al2O3, but I could not find the phase diagram between potassium cryolite and alumina. Please give me the satisfactory answer

11 December 2018 7,821 3 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

12% ledeburitic cold work tool steel, etched for revealing retained austenite, any help for clarifying?

Hello everyone. Given microstructure image belongs to a 12% ledeburitic cold work tool steel (annealed and tempered). The sample was etched with picral (100 mL ethanol and 4 g picric acid). I...

02 March 2021 4,119 3 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View

Is there any research regarding how training and development is going to change in the era of Fourth Industrial Revolution?

As the organizations getting prepared for the fourth industrial revolution, to enhance the skills of their workforce what type of changes are necessary and going to occur in the training and...

01 March 2021 3,199 3 View

How Can I bring as much common elements in steel as possible to calculate stable phase(s) in OpenCalphad?

As I was tweaking step-by-step OpenCalphad6 Macros step1.ocm involving phase and thermal property calculation of a High-speed steel, I could not incorporate more than 6 elements in the steel...

01 March 2021 8,840 1 View

I need to accelerate corrosion in steel parts that are used in a salt-water environment. Is there a technique for doing so?

I have a structure that employs d-ring swiveling tie-downs that corrode during use and become "frozen". I have sample swivel assemblies that I wish to corrode to see if I can free them using one...

01 March 2021 3,739 3 View

Why is my platinum counter electrode getting dirty during electrodeposition?

I am conducting anodic electrodeposition of MnO2 onto a stainless steel substrate, using a platinum strip as a counter electrode. This is done galvanostatically, with the current held between 5...

27 February 2021 1,829 3 View

Gas sensor response and recovery time independant of flow rate and chamber volume?

I am trying to obtain the response and recovery times for my gas sensor device. It appears the the response/recovery times are primarily dependant on the flow rate of the gas I inject into the...

26 February 2021 1,511 3 View

Is anyone working on a project focused on immigrants/newcomers working in the hospitality industry and how they have been impacted by COVID?

The on-going Covid-19 pandemic has had devastating economic effects on many industries. However, few have suffered to the same extent as full-service restaurants. Numerous studies have shown that...

24 February 2021 9,496 4 View

What is the optimum time and temperature of blanching and pre-frying potato for frozen fries?

I am helping a local home industry for developing frozen fries from their local farm. I want to know what is the optimum blanching and pre-frying temperature and time for processing. Please also...

23 February 2021 1,616 5 View