How could I use the bridge coupling method or a similar method linked to vehicle bridge interaction or just bridge response to develop a model to illustrate the response of a bridge vehicle?
If you are using EUROODE you can refer to loadmodel for dynamic or vibration response of a bridge deck.
Sir, I appreciate your thoughtful suggestion. I'll investigate it further.
Thank you
Please look at the following article:
Article Dynamic Analysis of Suspension Footbridges Using an Actual P...
Hi, I am using GROMACS 5.1.4 to simulate water in contact with a surface. I am only interested to calculate some properties of water near the surface. Let's say at a distance of x nm from the...
03 March 2021 9,989 2 View
Hi researchers, I am searching for some accurate way to do the circuit modeling of planar CPW-fed monopole antennas. I have gone through the literature where mostly circuit modeling is done using...
28 February 2021 7,016 1 View
For example in one research article the Elemental analysis values of COF-TpPa-1 ( Triformylphloroglucinol (Tp) (63 mg, 0.3 mmol), Paraphenylenediamine (Pa-1) (48 mg, 0.45 mmol) are as follows...
24 February 2021 1,265 6 View
24 February 2021 4,833 3 View
Research Question: Are red grouse (Lagopus lagopus scotica) a statistically significant proportion of raptor (bird of prey) diets? I am planning on using a series of G-tests (determining whether...
23 February 2021 5,827 3 View
What low-cut filter (high Pass frequency) to be used for the response spectrum (Tripartite plots)? I am currently working on differentiating between hard/soft site responses in Indo-Gangetic...
21 February 2021 9,273 2 View
Most of the data sets on the network only contain good information about the voltage and internal resistance of lithium batteries. The data of faulty battery is missing. Who can help me, I will be...
21 February 2021 8,659 1 View
Hi, everyone. I am considering the heat conviction during compacting simulation by Abaqus. I was wondering that how to define the sink temperature and film coefficient? Is there any references...
21 February 2021 6,197 1 View
According to the Sentinel-2 user guide here (https://sentinel.esa.int/web/sentinel/user-guides/sentinel-2-msi/naming-convention), the compact naming convention is arranged as...
21 February 2021 5,919 9 View
Hi, any one please guide me; SSR primers are species specific or trait specific. i have few primer which was reported in articles for wheat yield can i use these similar primer for lentil yield...
20 February 2021 315 4 View
i have frequencies of bridge that are effected by mass of vehicle. the problem is when any vehicle pass the bridge it would add the its mass to the bridge mass ultimately mass of the bridge will...
22 February 2021 10,004 3 View
Hi, I have modelled a three-span arch bridge with soil fill over along with pedestals. The FE modelling is done in LUSAS with HX8M solid elements (i.e. 3D solid modelling). The non-linearity is...
20 February 2021 1,346 2 View
I am trying to model a DAB converter and I need to observe the power transfeered to the load side on varying the phase shift between two bridges, hence I couldnt take a constant load e.g...
09 February 2021 6,489 3 View
My Hg/HgO electrode was used for EIS test in 4M NaOH solution. I found something in the salt bridge. After that, my EIS results found the noise at a low frequency (tested in a faraday cage)....
16 January 2021 1,900 1 View
I would like to know more about the following issues: 1. Using images as feedback for the closed-loop control of civil structures 2. Simulating the vision-guided control on the computer without...
03 January 2021 7,566 1 View
I know that frequency depends on material properties, geometry, support conditions and in plane loading. I have played around with these figures except that I maintained the same material steel...
26 December 2020 4,877 9 View
For modeling bridge deck slab on ANSYS APDL, why is shell element preferred over solid element? I read somewhere that the mesh of shell elements is more efficient than solid elements. Why is that?
02 December 2020 8,222 3 View
I want to reduce the disulfide bridge in my 7kDa protein. My protein has only 1 cysteine at the surface and thus makes a homodimer using a disulfide bridge. I want to reduce the disulfide bridge...
24 November 2020 3,211 5 View
For the bridge shown below, the web is connected to both flanges, and the slab is connected to the parapet by meshing and merging the nodes, but what is the name of this connection? is it...
22 November 2020 2,288 5 View
I modeled a bridge on ANSYS APDL and added cross bracings / diaphragms as shown below. The diaphragms are not straight along the x or y or z direction, they are inclides BEAM188 elements. how can...
14 November 2020 8,172 3 View