17 February 2021 0 9K Report

Can anyone suggest me a bidirectional buck boost dc dc converter module. I want to charge and dischrage batteries using this module. I want to control this module using PWM generated my Microcontroller.

Thanks in advance.

More Kranthi Kumar Banala's questions See All
Parallel connection of Lead and Lithium batteries?

Hello, Now a days, paralleling of batteries is being done among different chemistry of batteries. Suppose, if I connect lead and lithium batteries in parallel. What will be the current...

17 March 2021 5,231 3 View

Parallel connection of Bidirectional Buck boost converter?

Hello, I am doing some research work on the parallel connection of the bidirectional buck boost converter. I will upload the schematic at the end. Using the converters, I charge and discharge...

15 March 2021 8,484 4 View

Bidirectional buck boost converter?

Hello, I am charging and discharging battery using bidirectional converter. After reading some documents I thought buck boost topology would be better. But I could not find that evaluation module...

15 February 2021 8,149 5 View

Different chemistry of batteries in a storage system

Hello, As we know we use same kind of batteries in a storage system. We can increase current or voltage by connecting them in parallel and series connection of batteries. That is if we use same...

01 January 1970 5,011 2 View

Similar questions and discussions
Why chloride turns into chlorine gas in a Downs cell?

I imagine the battery drives the graphite into a carbocation, then chloride is oxidized to donate the electron to the carbocation, but what pushes the lost electrons of chloride to be shared...

03 August 2024 5,384 0 View

Regarding a model for simulating battery charge and discharge, what do you consider to be high fidelity?

Regarding a model for simulating battery charge and discharge, what do you consider to be high fidelity? What is the acceptable percentage of error (regardless of the metric)? Could you suggest...

03 August 2024 5,358 0 View

Good day!! All, can anyone recommend the best battery related journals to download research articles please?

I am an Mphil research student and looking for high impact factor battery related journals to download and read research articles to improve my knowledge and get new ideas in the field of battery...

01 August 2024 6,516 2 View

Flow through curved domains?

Hi everyone, I am working on a curved domain in which a ship is situated in the middle (geometry is given below). In my understanding the general fluid flow is parallel to the x axis from inlet to...

25 July 2024 9,058 4 View

I obtain two plateu instead of one in LFP cathode assembled with graphite anode in 1M LiTFSI in DOL/DME, what does this mean?

I have attached the charging curve from the battery tester for review. I need help on what is happening

21 July 2024 6,898 2 View

Hello, please if any researcher work in ion battery help me,?

I need to plot cycle number vs. capacity with multicurrent density. please let me know if my steps are right or not as the below picture

14 July 2024 7,702 2 View

Can an average household DIY spot welder be used for pouch cell electrode tab?

Would an average spot welder suffice for welding tabs for pouch cell electrodes instead of an ultrasonic one? Why would an ultrasonic welder be better than a regular spot welder?

10 July 2024 8,763 0 View

How to install Quantum Espresso with Intel compiler ?

Hello ! I would like to do band structure calculations of perovsikites materials with quantum espresso. For this I installed the Intel Fortran compiler. This is what I get when I run the...

08 July 2024 1,207 0 View

Why NCM cathode slurry has coating problem?

I tried to make slurry for NCM cathode but there was problem in coating process. The detail of my experiment is following; The ratio between active material(NCM811), conductive additives(Super-P)...

08 July 2024 7,327 4 View

How to realize charge and discharge of in-situ batteries in PPMS? Is there any expert scholar who can give me some advice?

The difficulty lies in how to miniaturize the battery. The sample holder is only 6.5mm, which means that the width or height of the battery cannot exceed 6.5mm (the height is about 3cm). I hope...

05 July 2024 8,141 0 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close