Can we block unwanted images during the x-ray prediction?

i am try to classify the x-ray images. During classification , can i block unwanted images (except x-ray image).

03 March 2021 7,100 1 View

Solar energy production forecasting ?

Hello everyone! I am interested in the topic of solar energy production forecasting for a ground-mounted PV system of more than 100MW capacity. Can anyone please suggest what are the main data...

08 February 2021 6,834 5 View

Why AC cables are always covered with the sand first and then covered with soil in solar park ?

I was curious to know why we only use sand for covering the AC cables inside the trenches and instead of having good isolation why these cables are covered. Why is there a problem in the trenches...

13 January 2021 6,008 3 View

Error encountered in executing MCE ?

In Terrset, an error encountered in executing Spatial Decision Modeller (MCE). During execution or run the MCE a massage come on the screen that reflects "Your columns and rows are not same" , I...

07 December 2020 1,542 1 View

How to separate epithelial cells?

Hello everybody, Hope you all are doing fine during this difficult time. I am trying to culture mouse oviductal epithelial cells but, the problem is when I culture them there is a mixture of...

31 October 2020 2,640 4 View

How to do extract Urban Heat Island separately from LANDSAT image for each land classes?

I have already been read many articles and found some methods but those are not cleared to me. Can you please suggest me how to generate different LST map of each land classes using ArcGIS? Or...

25 October 2020 5,978 5 View

Can someone advise me to do Rietveld Refinement of the material whose Crystallographic Information Framework (CIF) file is not available?

10 October 2020 7,411 9 View

What can you interpret from the estimate of NDVI and LST?

I had estimated the Land surface Temperature and Normalised Difference Vegetation Index, the result shows they have positive relation both increases in lower south part areas and higher in upper...

11 September 2020 6,021 4 View

Can entropy be reversed? In the Sci-Fi movie TENET, the concept is used to reverse time, is it possible theoretically?

Second Law of Thermodynamics states that as usable energy is lost, chaos increases - and that progression towards disorder can never be reversed.

01 September 2020 2,528 37 View

CG relaxation with B3LYP in VASP?

I am trying to CG relax a amorphous GeSe system with B3LYP and single K-point (gamma). Even though I have a 250 atom model, the calculations seem to be extremely slow. Is there a way to speed up...

23 August 2020 8,848 4 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

What techniques can I use to determine the miscibility of polymer blends?

The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...

03 March 2021 4,107 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View