12 December 2012 0 8K Report

I want to convert a barycentric interpolation function to partial fraction form. I want to know how the degree of the numerator as well the degree of the denominator has to be chosen. Does anyone know the Matlab code?

More Athul Shaji's questions See All
How to represent 3D data on an unstructured grid using Python?

I have a solved Laplace equation on a 3D geometry using finite element method. The potential values at each of the nodes are evaluated. I want a way to visualize the result, potential distribution...

02 March 2019 233 1 View

How to solve Laplace equation using edge element basis function?

I am trying to model the Laplace equation using finite element edge with element basis functions. I have written code using node basis function to solve the problem. The results obtained using...

31 December 2018 2,894 1 View

How to implement filter stage in non-negative matrix factorization?

In the blind signal separation of audio signals using non negative matrix factorization there is a filtering stage. How to implement this stage? Please see the attached file.

05 June 2018 6,853 0 View

Need some materials on Green's function analysis.

I am working in the field of CEM. I am learning MoM technique in CEM. Green's function is an integral part of this. Please suggest some good reading materials for this topic. You can mail the pdfs...

10 November 2012 6,174 8 View

Which CEM algorithm (comparing FDM, FDTD, FEM ,MoM) is better for antenna design, high speed interconnects etc?

There are many algorithms for numerical design. I know that each algorithm has its own advantages and disadvantages. But I would like to know which of these is better for antenna design and...

09 October 2012 4,111 13 View

Difference between artificial magnetic conductors (AMC) and high impedance surface (HIS)?

Is there any difference between artificial magnetic conductors (AMC) and high impedance surface (HIS)?

06 July 2012 6,216 4 View

How to create a unit cell of an AMC in CST Microwave Studio?

Hi, I need to design an AMC cell in CST Microwave Studio and obtain the reflection phase vs frequency diagram. Some of the steps that I used to design an AMC cell have been given below. Please go...

05 June 2012 9,579 1 View

What are the recent trends in planar Leaky Wave Antenna (LWA) design?

I have gone through some of the literature available on LWA. It has been found to be a narrow beam antenna with high directivity. Can anyone suggest some interesting ideas regarding planar LWA?

04 May 2012 5,967 5 View

Similar questions and discussions
MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

How Can I bring as much common elements in steel as possible to calculate stable phase(s) in OpenCalphad?

As I was tweaking step-by-step OpenCalphad6 Macros step1.ocm involving phase and thermal property calculation of a High-speed steel, I could not incorporate more than 6 elements in the steel...

01 March 2021 8,840 1 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close