How to define hyperelastic of orthotropic materials ,and get the parameters needed in Abaqus?

08 September 2016 6,201 0 View

About Holzapfel parameters in Abaqus simulating hyperelastic?

08 September 2016 1,409 0 View

How to determine the ""normalized volumetric compliance" when define visoelastic material behavior?

07 August 2016 9,957 1 View

Problem about measurement of elastic modulus of wood?

07 August 2016 2,554 3 View

How to simulate the placity of wood in Abaqus or Ansys?

05 June 2016 2,886 2 View

How to get the nomarl force of a surface in abaqus?

Recently, I encountor a question like the title, When i simulate a interference fit model, i want to get the narmal force of the contace surface, so i use the CFN, but my the normal of my surface...

02 March 2016 8,672 7 View

Who can tell me How to measuer the elastic modulus and Poisson ratio of adehesive?

02 March 2016 8,392 2 View

Who can tell me how to define a Amplitude maganitudes with tabular ?

02 March 2016 4,660 6 View

How to determine the inatial damage energy of cohesive element in DBC?

01 February 2016 3,551 8 View

Any advice on the damage of cohesive element?

11 December 2015 2,308 4 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Which cell line should we use to perform biological dosimetry experiments?

We are preparing some experiments based on irradiating cells under different conditions in order to evaluate the effects in terms of DNA damage, genetic expression, etc. As our project is...

01 March 2021 3,355 3 View

Is anyone familiar with the cyclic compressive fatigue testing (BS EN 12697 - 25) ?

I would like to get more information on the cyclic compressive fatigue testing (BS EN 12697 - 25) which is typically done for bituminous material in pavement design. Any one can advise on the...

28 February 2021 2,004 3 View

How to modify Johnson cook equation in ABAQUS?

I wanted to add an extra parameter to the existing Johnson cook equation in the ABAQUS simulation. How to add those extra parameters. Ref: A modified Johnson-Cook material model with strain...

28 February 2021 4,841 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

For modelling epoxy-based matrices (in composites), which model in ABAQUS is the most suitable, Concrete damaged plasticity or Drucker-Prager model?

I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...

28 February 2021 5,415 1 View

How to find the right number of integration points in second order 3d finite elements?

I am familiar with finite element simulations and numerical schemes like the Gauss Legendre quadrature. I also know that the Gauss integration yields exact values for polynomials up to degree 2n-1...

27 February 2021 6,818 3 View

B-mercaptoethanol (BME) protocol?

Hi everybody, I have been running a multiplex IHC which allow me to stain the same tissue with different markers (Primary Ab + Secondary conjugated Ab) (AF487, AF555, AF647). Since I would like to...

27 February 2021 5,028 2 View

What could be the reason for not having further low chi square value (better agreement) in my refinement result?

I have tried every combination of parameter changes and after that i have a poor chi square value. I can't get it lower any further. I know there have been a lot of discussion about Rietveld...

26 February 2021 8,480 3 View

What is the best way to calculate the angles of twist for concrete columns subjected to torsional moment using finite element software?

In Finite element software like ANSYS , there is difficulty in obtaining direct results of twisting of concrete members because SOLID65 which is the unique element designed to represent concrete...

26 February 2021 3,806 2 View