Any one is using INTERSECT SLB Software?

06 June 2015 0 2K Report

Hello There,

Anyone is using INTERSECT SLB Software in here? If so, would you please let me know if the simulator produces same result for fine scale large models as Eclipse itself or there is some reduction in accuracy? Did anyone compare the results of two? Thanks in advance.

Badges
Science topic

More Khaldoon Al-Obaidi's questions See All

Weibull fading matlab codes ?

hello I tried to looking for Weibull fading channel matlab codes and i found just the following formula: h = lambda.*(-log(rand(nRx(jj),N)).^(1/beta)) my question is this codes express the...

09 December 2020 6,575 1 View

Why COS 7 Cells change its morphology to round shape (rounded nucleus and peri nucleus cytoplasm) after Transfection?

I have transfected COS 7cells to express Protein-GFP conjugate, transfection rate was very low (20-30 %) , but the cell morphology changed, many of the cells appear round, (nucleus round too)...

15 September 2020 5,324 3 View

What is the effect of the Gypsum percentage on the collapse potential of the soil?

What is the effect of the Gypsum percentage on the collapse potential of the soil? The collapse potential (CP) of the soil can be calculated by the Single Oedometer Test or Double Oedometer Test.

30 June 2020 150 19 View

What are the main characteristics of this residual soil?

Residual soil is the product of the weathering processes for rocks. What are the main characteristics of this residual soil?

10 June 2020 6,994 49 View

Is there any effect of the liquid type on the collapse deformation in single Oedometer collapse test (SOT)?

Single Oedometer collapse test (SOT) is the relationship between the void ratio and vertical stress under dry conditions until reach to collapse stress such as (200 kPa) then flooded the soil...

25 April 2020 5,966 4 View

How can I get Absorption spectrum for organic molecules ?

How can I get Absorption spectrum for organic molecules (Pentacene(C22H14) ,TFB (C53H67N), CuPc (C32H16CuN8), ZnPc (C32H16N8Zn), Alq3 (C27H18AlN3O3), 6P (C17H21N5O5), and HATNA (C24H12N6), i.e the...

09 April 2020 6,625 4 View

What is the best method for particle size analysis of gypseous or salts soils?

Dear researchers, Conventional particle analysis of soil sample using ordinary sieve analysis in both dry and wet methods on sieve Nr. 200 of opening size 0.075 mm according to ASTM standard or...

09 March 2020 8,349 4 View

Can anyone provide me geometry of an axial pump with induced with mesh and setup using CFD fluent?

I am working to simulate axial pump with inducer using CFD fluent and I need help to known how can create axial pump that mean how can rotate impeller with fixed the pipe wall under transient...

07 February 2020 5,315 3 View

Online website for to calculate Homo and Lumo?

Where can I find the best online website for to calculate Homo and Lumo

11 December 2018 9,073 1 View

Homo and Lumo?

What is the best online website for to calculate Homo and Lumo

11 December 2018 1,775 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein?

Hi In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein? I got this error in the add-ion stage: Fatal error "./ amber99sb-ildn-HHH.ff / force...

01 March 2021 8,747 4 View