05 September 2018 3 3K Report

Dear Professors

What is the main parameters we have to measure to evaluate the quality of air in cities , we have different sources of air pollution such as cars , generates , refineries .... in addition to the lacking in vegetation growth and sand storms .

Thank you

More Mazin N Fadhel's questions See All
Are virtual conferences close to the results of classic conferences?

What is the approach ratio

30 December 2020 4,701 9 View

What types of stationary phases and solvent conditions are used for protein purity analysis via thin layer chromatography??

I have a protein labeled with a fluorescent dye (fluorescein) and I am hoping to get a quick measure of purity using TLC after dialysis. TLC is quick and easy so I am hoping to start there. What...

15 November 2020 7,319 3 View

Hi for every one I need the primer for ABO rs495828 ( ARMS or allele specific PCR)?

the primer for PCR ( ARMS or allele-specific ) for scientific research either from the studies or someone who has the ability to deisgn the primer for me as a required features above/ thank a lot...

20 September 2020 224 4 View

What is the effect of level of sulfur on chemical resistance of rubber compounds against acid solutions?

I study the relation between the amount of sulfur of rubber compounds and the chemical resistance of rubber compounds to prepare rubber compounds using for lining acid contained.

14 September 2020 8,229 3 View

Some of the universities held the conferences based on virtual technique because of the pandemic?

What is the scientific sides to this conferences?

09 June 2020 8,047 1 View

Are there any sound of respiration datasets related to COVID-19?

I try to analyze the respiration of humans that infected with COVID-19, Anyone has the dataset of that disease? we seek cooperation with scientific research.

20 May 2020 1,080 2 View

Hello all, could any one help me to find the properties of parrafine wax that I need to model this type of wax in Abaqus?

If any one know how to model wax in Abaqus that's will be very helpful.

27 October 2018 8,165 2 View

How to calculate kWh in a PV solar concentrator?

Hi All, I got confused in finding the proper method to calculate the kWh(Energy) that can my solar concentrator produce in a certain location. I 've got the Peak Sun Hours (PSH) calculated which...

04 September 2018 2,270 2 View

What is the ROC curve analysis?

Currently, I am working on medical image processing. So What is the ROC curve analysiscan be use for the classifiers?

02 March 2018 2,082 4 View

What are major problems in medical image segmentation?

Currently, I am working on microscope image segmentation. Is the any recommended about major problems in medical image segmentation

26 November 2017 9,163 8 View

Similar questions and discussions
Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

How to calculate average trend in maximum annual NDVI from MODIS?

I am wanting to calculate the average trend in maximum annual NDVI in Iceland from 2010-2020 using MODIS MYD13Q1 V6. How would I do this? I have currently inserted the NDVI bands from the MODIS...

02 March 2021 752 2 View

LEDs on Vis Light photo degradation of MB water sol via N doped TiO2 in a mini flume?

Good day to all, I have no experience with light emitting diodes. I am building a glass mini flume to demonstrate the photo degradation of Methylene Blue in water running over self cleaning...

26 February 2021 4,026 5 View

Why do the air flow results vary totally when adding scalar in CFD ?

Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...

25 February 2021 9,602 4 View

Fractional impervious surface (FIS) map ?

Need Help Does anyone Know how to make a Fractional impervious surface (FIS) map from NDVI map, in ArcGIS environment? Thanks in advance

24 February 2021 8,455 2 View

Is is possible to pole with corona poling pellets of the sample material instead of thin films?

As it is highly probable that pellets will have a higher degree of air gaps and voids than thin films, is it possible to pole the samples with corona poling nevertheless? Or is there the...

24 February 2021 1,349 1 View

To date, according to health authorities, 30% of the population's diseases are initiated by drinking water pollution. Do you know this problem?

The main studies are as follows: * regular and timely receipt of information about the state of the environment using automated systems (stationary and mobile); * operational analysis of the...

23 February 2021 912 5 View

Have you ever experiencing air vent trouble in fermentation process?

Dear all, My research group is currently working with a 12-litre fermenter. Somehow, if we do the fermentation for more than 20 hours, the process will be more prone to contamination. Our current...

23 February 2021 1,908 2 View

Help with assigning pressure boundary conditions in FLUENT on a large structure?

Hello, I created a very tall tower (>1000m) and applied pressure boundary conditions at the inlet (bottom) and outlet (top) that correspond to the pressure are their relative altitudes....

22 February 2021 9,972 4 View

What type of pressure sensor are usually used in microfluidics?

My team is designing a dual channel microfluidic chip that runs air and water. I think we've decided on the NE1000 syringe pump for it's versatility and feedback control. We will be ordering the...

18 February 2021 9,928 2 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close