A positive Lyapunov exponent implies chaos. Whether a positive value of Lyapunov exponent in the order of 10^-4 or 10^-5 represents chaos?

More Ankit Tiwari's questions See All

How does SEA software normally number subsystems?

Dear colleagues, What is the common subsystem numbering system in SEA modelling software (i.e. VA One, AutoSEA2)? Cheers, Feng

27 February 2021 7,073 3 View

What low-cut filter (high Pass frequency) to be used for response spectrum (Tripartite plots) ?

What low-cut filter (high Pass frequency) to be used for the response spectrum (Tripartite plots)? I am currently working on differentiating between hard/soft site responses in Indo-Gangetic...

21 February 2021 9,273 2 View

How to remove the species data from rda data frame in R (only remain the sites/samples point)?

Dear everyone, When I using the rda function in r, I met this question. As you can see in the figure, there are a lot of deep blue points which refers to the species. But I would like remain...

15 February 2021 8,982 2 View

How to characterize epitopes within a peptide sequence?

Greetings In a theoretical perspective, I want to use a human-derived peptide as a plausible antigen but the problem associated with tolerance hampers my approach. Then I thought why not denature...

20 January 2021 2,201 1 View

How can I generate a population with a fixed correlation coefficient in R?

I want to generate an artificial population using two variables (say x & y) with a fixed correlation between x & y. Which package/command in R software can help in this?

18 January 2021 2,545 9 View

How to Extract DNA from dried rhizomes, wood, galls etc. stored for a long time?

Dear Respectable Scientists, I have been trying to extract DNA from above mentioned sources using different CTAB/SDS Buffer Compositions and purifying agents but I am not able to extract DNA from...

12 January 2021 5,899 8 View

Which one is best theoritical model that takes account interfacial thermal resistance while predicting thermal conductivity fiber/polymer composites?

Hello Everyone, I want to know about best analytical model that consider the interfacial thermal resistance which predicting the thermal conductivity for fiber/matrix composites. Here, Best...

30 December 2020 6,375 2 View

Please suggest ways to perform Discreet Element Modeling (DEM) on stabilized clayey soil; is it effective to simulate clay for DEM analysis?

I am looking for answer considering modelling in PFC

26 December 2020 5,509 1 View

Find value of heat transfer coefficient in SI units??

A tube is subjected to air at standard temperature and pressure conditions with velocity 5 m/s. initial temperature of the tube is 980 K and drops to 500 K after interaction with the cool air....

21 December 2020 6,408 3 View

No title

Hi, I am interested to see the effect of BCG on macrophages (microglia )Therefore , I would like to know the amounts and the routes of administration which is safe in mice and how long is...

20 December 2020 7,166 2 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

Why does two different bioinformatics tools for the same proteins show different subcellular localizations?

During a computational analysis, I found that for a protein of a plant, two different subcellular localizations are seen using CELLO and WoLF PSORT. For example, in CELLO, it identified the...

01 March 2021 6,729 2 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

How to prevent ANFIS Model from negative prediction values in MATLAB?

I have input and output data set for "ANFIS modeling in MATLAB", and I am getting some negative predicted values of output in testing. However, the predicted values of output in training are...

28 February 2021 3,459 3 View

High aspect ratio hexahedral mesh optimization solver?

I am interested in evaluating mesh optimization solvers that converge to high aspect ratio unstructured hexahedral grids. In other words, I am interested in a solver that optimizes warpage,...

26 February 2021 7,279 2 View

How does an AC-DC power supply Flyback Converter Based USB Charger Model using Matlab/Simulink looks like?

I am required to learn about Flyback converters and I got stuck not knowing to full design of the power supply flyback converter Based USB Charger Model using Simulink, especially the design model...

25 February 2021 5,435 2 View

Please. Could you help be in implementing Fractal Discrete Cosine Transform algorithm in Matlab?

I do need the Matlab code of Fractal Discrete Cosine Transform (FDCT). Can anyone who has already implement this code, help me with the implementation of this transform?

24 February 2021 5,602 2 View

Error in comsol?

Dear respected researchers, while performing CFD analysis in Comsol it's showing like this Error: Nonlinear solver did not converge. The maximum number of Newton iterations reached can...

24 February 2021 249 3 View

D2D implementation in Matlab in Vienna LTE software?

Hi Hope you are well. Can you please share your code for D2D implementation in Matlab. I want to implement D2D in Matlab based Vienna simulator and struggling to deploy D2D. Thanks

24 February 2021 9,378 3 View

Vyacheslav G. Rybin

Try reducing the step size and repeating LLE calculation. it's not clear what system under your investigation.

I believe that your results can be interpreted as a periodic behavior.

Ankit Tiwari

Vyacheslav G. Rybin Thank you for your response. As suggested, I will recalculate the Lyapunov exponents with the reduced step size.

My question is not for any specific system. I wish to know the infimum value of the positive Lyapunov exponent for a system.

Omar Laith

https://libraryapp.uomustansiriyah.edu.iq/ebooks.php?a=view&recid=2789