3D RMS of Kinematic PPP?

11 April 2023 0 9K Report

I used RTKLIB software for kinematic PPP solving, and how to get 3D RMS？

Badges
Science topic

Similar topics
Correction

More Shuanglei Cui's questions See All

How to replace Zeocin resistance gene in Pichia genome after integration?

I have been using Zeocin marker for target protein expression to verify integration in Pichia system. However, I would like to remove Zeocin marker since it's antibiotic related and not ideal for...

15 June 2024 3,851 2 View

Dear Doris, Could you please give me the code in your paper "On Causal Discovery from TimeSeries Data using FCl"?

my email is [email protected]. thank u very much!!!

10 March 2024 6,991 2 View

Errors when calculating dielectric constant of TiN?

I was trying to calculate dielectric constant of TiN. I did self-consistent calculation first and then run the calculation of dielectric constant with INCAR like this: PREC = Accurate ALGO...

16 February 2024 8,951 3 View

Ansys fluent_adapting mesh?

I use adapt-gradient and refine mesh by phase(air and water). But when calculate running it turns to Warning—— Adapting mesh (Adapt Gradient of water-vof)... WARNING: 2 cells with non-positive...

06 December 2023 1,565 1 View

Hello everyone, do you have the MATLAB source code that draws the limit cycle of ODE system?

Hello everyone, do you have the MATLAB source code that draws the limit cycle of ODE system? Can you share it with me? My email is [email protected]. If you can help me, I can share...

18 October 2023 1,028 0 View

How to dissolve lyophilized silk fibroin?

I have prepared silk fibroin from cocoons following the protocol established by the Kaplan group. However, in their protocol, they specified that "silk fibroin can be frozen under -80 or -20...

13 September 2023 902 0 View

How much information can we get from the UV-IRS spectrum for semiconductor?

Usually, I obtained optical band gap for semiconductor through Tauc Plot method which only focus only on the region near the intrinsic absorption edge. I wanna know what does the rest part of the...

20 July 2023 8,569 0 View

Why cubic phase tends to form at high temperature?

According to the principal of entropy increase, it's easier to form more disordered crystal strcuture at low temperature. Do I mixed up the concepts of chaos and disorder?

17 July 2023 290 1 View

Why HMIMO is called holographic?

Here are my detailed question: As I can see, the H in HMIMO should stand for holographic and it should obey holographic principles. But as I read more HMIMO papers, especially this one:Holographic...

05 June 2023 2,547 1 View

Whether there are some key factors for breaking through to the D larvae?

I wanted to understand the mechanisms of the oyster larvae and whether there were some key factors for breaking through to the D larvae.

26 April 2023 728 3 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Would you like to join our meta analysis research team?

I am excited to announce an opportunity for dedicated researchers to join our dynamic team for an ongoing meta-analysis study. If you are passionate about research and have a keen interest in...

01 August 2024 6,737 1 View

CAD File of human's & rat's respiratory airways ?

Dear all, I am working on particle deposition in human's & rat's respiratory airways using CFD and I am looking for the 3D CAD file for my simulations (STEP or IGES format). If somone has such...

29 July 2024 1,092 2 View

Cell optimization in 1D Nanotubes?

Dear All, I use Quantum Espresso. I want to optimize the structure of the carbon nanotube using the vc-relax. I got confused about how to fix cell_dofree here. For 3D, cell_dofree = 'all' or...

22 July 2024 5,708 0 View

Comment évaluer une politique de financement dans le sous-secteur de l'enseignement supérieur?

La politique de financement est en soit une politique publique. Comment les évaluer dans un travail de recherche scientifique ?

22 July 2024 6,495 2 View

Seeking latest research on social protection in northeast Nigeria, Yobe state. How does it compare with other states?

What has been the social protection outreach like in Yobe state. Which areas are challenging for the government departments and what capacity building would be most effective? Comparison of the...

21 July 2024 9,887 1 View

How do you feel about social exclusion in transport within South Africa?

Research being conducted by Stellenbosch University would like your opinion about the effects of social exclusion on emerging urban mobility options and traditional public transport services. By...

21 July 2024 4,032 0 View

How to combat antibiotic resistance?

The increasing resistance of bacteria to antibiotics has made many infections difficult to treat, posing not only a threat to public health but also a major challenge to healthcare systems worldwide.

18 July 2024 6,688 3 View

How to classify 3D Bioprinting as a part of Additive Manufacturing?

Hello, I have a problem in classification of "Additive Manufacturing" techniques. There are several classification for Additive Manufacturing e.g. Powder, Extrusion, Resin etc. Actually, I am OK...

15 July 2024 139 3 View