Explain your ideas
Hi, I am using GROMACS 5.1.4 to simulate water in contact with a surface. I am only interested to calculate some properties of water near the surface. Let's say at a distance of x nm from the...
03 March 2021 9,989 2 View
01 March 2021 7,254 3 View
What is the disadvantages of high sulfur content to the ceramic burning process? and what is the effect of outranged viscosity?
24 February 2021 8,219 2 View
Research Question: Are red grouse (Lagopus lagopus scotica) a statistically significant proportion of raptor (bird of prey) diets? I am planning on using a series of G-tests (determining whether...
23 February 2021 5,827 3 View
What low-cut filter (high Pass frequency) to be used for the response spectrum (Tripartite plots)? I am currently working on differentiating between hard/soft site responses in Indo-Gangetic...
21 February 2021 9,273 2 View
Most of the data sets on the network only contain good information about the voltage and internal resistance of lithium batteries. The data of faulty battery is missing. Who can help me, I will be...
21 February 2021 8,659 1 View
Hi, everyone. I am considering the heat conviction during compacting simulation by Abaqus. I was wondering that how to define the sink temperature and film coefficient? Is there any references...
21 February 2021 6,197 1 View
According to the Sentinel-2 user guide here (https://sentinel.esa.int/web/sentinel/user-guides/sentinel-2-msi/naming-convention), the compact naming convention is arranged as...
21 February 2021 5,919 9 View
Hello Everyone, I tried to form ZnS nanoparticles using the hot injection method and was able to form the same (confirmed by XRD). When I centrifuged, after the reaction I got a kind of white...
17 February 2021 1,709 3 View
A software which can help to design the experiment, store data, update new data, set subculture reminders, barcoding etc. Like Invitrosoft.
17 February 2021 3,015 5 View
Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...
02 March 2021 4,910 3 View
Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...
02 March 2021 1,999 5 View
during ultrasound examination of acute abdomen, sometimes we see free fluid , can we know the type of fluid ,whether blood or not , using ultrasound only? if yes , what are the sonographic...
01 March 2021 7,476 4 View
I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...
01 March 2021 6,985 3 View
I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...
01 March 2021 8,668 3 View
How can one improve mesh skewness, orthogonality, aspect ratio?
28 February 2021 7,730 3 View
I'm Juan Carlos, a high school student who is working with electropinning, I made an electropinning machine with a 21g needle and a 30kv high voltage source and the distance between my needle is...
28 February 2021 298 3 View
I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...
25 February 2021 2,615 3 View
Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...
25 February 2021 9,602 4 View
I have a pipe with 10 mm in Diameter and 2 bar pressure, the fluid velocity is 200 m/s, the fluid is air. is there a way to reduce velocity without affecting the pressure value?
25 February 2021 7,187 3 View
