1. How can I calibrate an Elbow flow meter? 2.What causes uncertainty in it?

Mahsa Babaee @Mahsa_Babaee4

12 December 2016 0 5K Report

Hello

I'm researching on "Elbow Flow meters" .

I was wondering if you wanted to explain how can I calibrate an Elbow flow meter?

could you explain what causes uncertainty , please ?

Best regards

Badges
Science topic

Similar topics
Psychometrics
Measurement

More Mahsa Babaee's questions See All

How can I get access to "begellhouse.com"?

Dears, All I urgently need is some conference articles that are only available online on "begellhouse.com", but the site is out of order and I face the error: 503 Service unavailable! I was...

10 November 2018 2,981 1 View

In simulation of pool boiling via fluent while input is heat flux the calculated temperature of the heated surface is more than what it should be Why?

Hello to every body.What I'm interested in is the simulation of pool boiling via fluent software. Mixed multiphase model is used. During my simulating bubbles have formed but while my input is a...

05 June 2017 929 2 View

What's heat transfer coefficient in boiling? How it's measured in experiments?

HTC= Heat Transfer Coefficient

06 July 2016 1,241 1 View

How to determine positive-stained cells in FACS? Use isotype or unstained control?

To compare positive and negative cell populations in flow cytometry, should I compare unstained cells with antibody stained cells? Or with the isotype control? Most papers show comparison with...

06 August 2024 6,728 6 View

Why do we equate male and female arousal?

Women, on the other hand, can become physically aroused (increased blood flow in the reproductive organs) without becoming psychologically aroused even in the slightest. (Robert Weiss)

05 August 2024 9,537 2 View

How does one derive the standard deviation of a scale?

Dear all, I am working on analyzing data from a survey on student satisfaction. The survey contains items with a 7-point Likert response format that produce 12 scales related to different areas...

05 August 2024 2,141 4 View

Why results of ROS flurescence are negative as there was no bacteria within?

Hello. I am working on ROS production of two systems: system A is cerium oxide and hydrogen peroxide, system B is cerium oxide nanoparticle, hydrogen peroxide and potassium bromide. I did some...

04 August 2024 5,974 3 View

How to make a Lateral flow control line more uniform?

We have a lateral flow test on Sartorius 140 NC. The conjugate is gold-monoclonal antibody. Using different control lines (GAM, protein A, protein G) we get a very strong leading edge with reduced...

31 July 2024 4,510 3 View

Question about combustion Kinetics ?

I am currently working on modeling FCC catalyst regeneration and have come across a point of uncertainty that I hope you can assist me with. In my previous models, I have utilized lumped kinetics...

30 July 2024 6,137 0 View

Suggestions for the Annexin V Positive Control ?

Hello everyone, I am currently using washed human platelets to stain Annexin V as a procoagulant marker. Additionally, I am staining with PerCP-CD61 to identify platelet cells. So far, I have...

29 July 2024 8,624 1 View

Why cannot i find my protein on cell surface after antibiotic selection of expressing plasmid?

I cannot confirm cell surface protein expression by flow cytometry even after transfection and antibiotic selection of cells. Does it take long for proteins to express on the cell surface? the...

28 July 2024 3,178 3 View

Why specific capacitance is not proportional with the specific surface area?

Dear researchers, Why specific capacitance is not proportional to the specific surface area? I have material A with a surface area higher than material B, but material B is showing little bit...

26 July 2024 9,156 2 View

Problem with Two-phase simulation?

Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...

25 July 2024 2,309 5 View