Production, Testing, Dimensioning, Research on Composites | Contact experts in Composites to get answers
4,586 views 532 posts
Questions related to Composites
Can any one tell me that can we simulate different orientation of bidirectional fibers by using any software..
27 December 2017 6,067 4 View
Keyword - current application. No properties, theories and irrelevant documents Thanking you
19 December 2017 8,564 5 View
I need the essential procedure for making natural fibre composite by hand lay up method.
14 December 2017 7,946 3 View
I am looking for a distributer that currently have TPS in stock, and where I could buy a small quantity for research purposes with which I could used to make composites..
13 December 2017 3,315 3 View
if we got shielding properties of composite 50%filler and 50%wax and achieved 23 dB shielding properties it is good or not? the filler is conductive polymer with low loading of CNT.
13 December 2017 1,019 3 View
How much filler % in matrix for EMI materials is good?
13 December 2017 2,034 3 View
I have prepared Natural rubber- Multiwall CNT composite with weight % ratio of 99:1. But it is highly flexible. Now i want to improve its stiffness at minimum level. So what material should i add...
11 December 2017 3,907 3 View
After photocatalytic degradation process, How to analyse the percentage of total organic carbon.
07 December 2017 4,572 3 View
Can anyone tell me about the elastic properties (first of all typical values of Poisson ratio) of unidirectional commercial high strength plastics such as HexPly8552/33%/134/IM7(12К) 0 ? Or is...
02 December 2017 7,159 5 View
I hope to make a compact electric circuit to control my module. Because module size is very small (diamter=11 mm, length=30 mm), I can't use general timer relay. My module operates as...
01 December 2017 3,678 2 View
Composite cements has superior physico-mechanical properties over those of Portland cement (PC).
30 November 2017 6,988 3 View
Bonded amalgam Vs. Non- Bonded amalgam Vs. Composite. In terms of flexion, leakage prevention and cuspal fractures Thank you
28 November 2017 4,916 1 View
I want to carry out carry out Mechanical characterization of fiber and matrix individually for Polymer Matrix Composites. SO kindly suggest me the ways to do the same.
22 November 2017 10,139 3 View
I have chosen the Hand lay-up process for preparation of glass fiber reinforced epoxy matrix composites. Now i want to Justify, why have I chosen the same? What are the parameters/points to be...
22 November 2017 3,563 3 View
During XRD i found the peaks of CuAl2O4, CuMo2S3, AlB12 compounds and i want to know the effect of these compounds on tribological properties of Copper matrix composite during dry sliding. Plz...
17 November 2017 500 2 View
I need to prepare a tensile specimen from a sample of diameter 40 mm. It is a composite of PCL-HA-Mg made via cold pressing. Also, suggest the astm d638 type which i should scale down?
09 November 2017 2,357 3 View
I'm currently doing an assignment and we have to come out with a manufacturing process. My group is planning to manufacture bicycle helmet by mixing coir fiber with epoxy resin and hardener but we...
08 November 2017 2,042 1 View
Hei, If wanting to do mode I testing of composites with thick bondlines (larger than 1mm) , does the insert film need to be less than 13um thick as recommended in the standard? Is there any study...
06 November 2017 4,694 1 View
How fabricate preforms of Al2O3 for infiltration casting in iron-based composite? like picture
05 November 2017 6,590 2 View
I am trying to analyze the XANES spectra taken in TEY mode of my various sample composition with PEO as my base sample. I want to compare the peaks position attributed to each transition...
27 October 2017 6,963 2 View
I have calculated the Stokes shift for pure liquid crystal material and Liquid crystal-nanomaterial composite system and the Stokes shift of pure Liquid crystal is greater than the composite...
26 October 2017 1,562 5 View
I have tpu pellets and nano powders. please suggest me the best procedure for preparing a good composite with injection molding.
25 October 2017 9,603 6 View
I would like to prepare UHMWPE composite.
24 October 2017 7,586 3 View
Hi, By which software and how can I estimate composite reliability (CR)?
23 October 2017 4,474 4 View