23 Questions 18 Answers 0 Followers
Questions related from Danial Nawaid Siddiqui
I have 6 different powder samples of Mechanically Alloyed magnetic High Entropy Alloy Powders as FeCoNiAlMn1-xCrx (x=0,0.2,0.4,0.6,0.8,1). I need to measure there microwave absorption properties...
25 July 2023 3,363 0 View
Basically I have powder samples of High Entropy Alloy Powders which are produced by mechanical alloying using Ball mill. I need microwave absorption property characterization of my samples but...
21 June 2023 1,289 3 View
I prepared FeCoNiAlMn and FeCoNiAlMn1-xCrx (x=0.2,0.4,0.6, 0.8,1) using Ball mill with 45hrs milling but for increasing the crystallinity of my powder alloy samples I need to heat them in vacuum...
03 December 2021 1,407 4 View
What should be the optimu heating temperature and heating time for high entropy alloy powder?
29 November 2021 5,309 3 View
I did XRD of my powder alloy samples, I got major peak of all samples with different concentration but beside major peaks some small distortion peaks, I think the high entropy alloy powder hasn't...
26 September 2021 4,671 4 View
I want to prepare FeCoNiAlMn1-xCrx for (x= 0.2,0.4,0.6, 0.8 and 1mol.) high entropy alloy powder by ball milling. But I am unable to calculate individual masses that will be required for making...
25 June 2021 7,727 0 View
Is there any research article regarding FeCoNiAlMn1-xCrx high entropy alloy system?
23 June 2021 5,786 1 View
Basically I synthesized an Equiatomic FeCoNiAlMn High entropy alloy powder by mechanical alloying of 45hrs using Ball mill. My main purpose is to enhance soft magnetic properties of my high...
10 June 2021 8,911 3 View
I synthesized an Equiatomic FeCoNiAlMn High entropy alloy powder. Now I am not getting getting any new idea that which element powder among Si, Cr, V and Sn can be substituted in place of which...
09 June 2021 9,715 0 View
I observed a 39 degree two theeta peak in my XRD pattern for my equiatomic FeCoNiAlMn high entropy alloy powder after 45hrs mechanical alloying and same after 50 degree two theeta also but not...
30 May 2021 7,795 2 View
Where I can get the JCPDS card for XRD pattern of FeCoNiAlMn High Entropy Alloy Powder?
30 May 2021 8,961 2 View
Hello guys need a help this is my XRD pattern of equi-atomic FeCoNiAlMn high entropy alloy powder as shown in red color after 45hrs mechanical alloying using Ball mill. But I am not sure about...
30 May 2021 5,821 4 View
Actually I prepared an equiatomic High Entropy Alloys Powder in which I used 20g total mass of five component powder sample in 50ml volume PQ-N04 high energy ball. So is this total mass of powder...
23 May 2021 671 0 View
I synthesized an Equiatomic FeCoNiAlMn High entropy alloy powder by 45hrs Mechanical alloying using Ball. Now I am not getting that among Si, Cr, V and Sn which element can replaced in FeCoNiAlMn...
22 May 2021 8,028 4 View
Hello I prepared an equiatomic FeCoNiAlMn High entropy alloy powder produced by mechanical alloying of 45hrs using Ball mill. I am not getting that among Cr, V and Sn which element can replace in...
28 April 2021 5,844 4 View
Hello I want to ask a question that I synthesized an Equiatomic FeCoNiAlMn High entropy alloy powder by mechanical alloying now I am not getting that among Si, Cr, V and Sn which element can...
26 April 2021 3,116 0 View
Which rare earth element powder can replace in equi-atomic FeCoNiAlMn high entropy alloy powder mechanically Alloyed for enhancing soft magnetic property of alloy system?
16 April 2021 4,647 0 View
I have prepared an equiatomic FeCoNiAlMn High entropy alloy powder by mechanical alloying for 45hrs. I want to know that which rare earth magnetic element powder can replace in equi-atomic...
15 April 2021 9,022 0 View
I synthesized an Equiatomic FeCoNiAlMn High entropy alloy powder through mechanical alloying of about 45hrs. Since I am investigating its magnetic properties. So will replacement of Mn by Si...
10 April 2021 2,435 2 View
Does replacement of Mn by Si enhances soft magnetic properties of equi-atomic FeCoNiAlMn high entropy alloy powder produced by mechanical alloying?
07 April 2021 1,485 2 View
I have developed an equiatomic FeCoNiAlMn High entropy alloy powder by mechanical alloying by 45hrs milling. But I am not getting which element I can replace in this equi-atomic FeCoNiAlMn high...
04 April 2021 5,663 2 View
I am preparing an equi atomic high entropy alloy powder FeCoNiAlMn by mechanical alloying previously this same alloy system with some element concentration change FeCoNi(MnAl)x with (Mn and Al...
03 April 2021 7,661 3 View
Which element we can replace in mechanically alloyed FeCoNiAlMn equi-atomic high entropy alloy powder to increase its soft magnetic properties?
01 December 2020 1,722 5 View