Why Plates are bending instead of moving forward as Load is applied in the tensile direction for Metal to composite bolt joint plates?

30 April 2023 0 2K Report

I'm doing abaqus simulation on Metal to Composite single lap bolt joint plates with one side has encastre BC and load on the other end. Simulation completes but it bends at the point of the joint, how can i fix it? it should not move along the direction of the load?

Screenshot has been attached.

Badges
Science method

More Sohail Raza's questions See All

How to analyze a particular region of my simulation box in GROMACS?

Hi, I am using GROMACS 5.1.4 to simulate water in contact with a surface. I am only interested to calculate some properties of water near the surface. Let's say at a distance of x nm from the...

03 March 2021 9,989 2 View

Can the Dunn's test be used as an appropriate post-hoc for the G-test?

Research Question: Are red grouse (Lagopus lagopus scotica) a statistically significant proportion of raptor (bird of prey) diets? I am planning on using a series of G-tests (determining whether...

23 February 2021 5,827 3 View

What low-cut filter (high Pass frequency) to be used for response spectrum (Tripartite plots) ?

What low-cut filter (high Pass frequency) to be used for the response spectrum (Tripartite plots)? I am currently working on differentiating between hard/soft site responses in Indo-Gangetic...

21 February 2021 9,273 2 View

Where can the fault diagnosis data set of lithium battery be found?

Most of the data sets on the network only contain good information about the voltage and internal resistance of lithium batteries. The data of faulty battery is missing. Who can help me, I will be...

21 February 2021 8,659 1 View

How to define the sink temperature and film coefficient?

Hi, everyone. I am considering the heat conviction during compacting simulation by Abaqus. I was wondering that how to define the sink temperature and film coefficient? Is there any references...

21 February 2021 6,197 1 View

How to discriminate between Sentinel-2 Level-2A Product Discriminators?

According to the Sentinel-2 user guide here (https://sentinel.esa.int/web/sentinel/user-guides/sentinel-2-msi/naming-convention), the compact naming convention is arranged as...

21 February 2021 5,919 9 View

Are ZnS nanoparticles moisture sensitive?

Hello Everyone, I tried to form ZnS nanoparticles using the hot injection method and was able to form the same (confirmed by XRD). When I centrifuged, after the reaction I got a kind of white...

17 February 2021 1,709 3 View

Can anyone suggest a software for running a plant tissue culture lab?

A software which can help to design the experiment, store data, update new data, set subculture reminders, barcoding etc. Like Invitrosoft.

17 February 2021 3,015 5 View

Is an encrypted dataset with Microsoft SEAL compatible with Cloudsim simulator??

Hello, I would like to do homomorphic encryption using Microsoft SEAL on my dataset and then use it as an input to the Cloudsim simulator to do clustering on. Is it possible and compatible with...

16 February 2021 3,915 1 View

SPSS - Merging files by ID numbers that contain letters?

Hi, I'm trying to merge files from a data base of 20 files, each containing about 4000 subjects. Unfortunately the ID numbers are actually a combination of numbers and letters (e.g., b1458219)....

15 February 2021 5,833 3 View

Waters 2707 HPLC autosampler problem?

I am using a 2707 waters HPLC device. When I try to inject a sample, it says missing plate or rack. I changed the needle and calibrated its position but I still get the same problem. I even get...

02 March 2021 1,408 1 View

Should we change media after1st 6hrs after plating HUVEC bought from INVITROGEN?it's not recomended by invitrogen.Will DMSO present in stock matter?

We have HUVEC bought from Invitrogen. Cat no -C-003-5c. while first plating the cells we have bought the protocol suggests not to centrifuge the cell with media to remove the DMSO. Should we...

02 March 2021 3,713 2 View

How to normalise data on OPM package from R Studio ?

Good afternoon, I recently used OmniLog from BIOLOG for my experimentations : I tested the metabolism of different strains on 2 types of plates. I have 16 strains of 3 different groups...

02 March 2021 3,584 1 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

How to assign different material properties to each element in Abaqus ?

Hello, I am writing a python script to generate my model and write the input file. The problem is I have 1000 elements in my mesh and I want to assign different material properties to each...

01 March 2021 9,511 3 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View

Benefits of the 24 welled plate?

We have always used the 96 welled plate, the 48 welled plate but apparently there is much evidence on the 24 welled plate and above all its benefits.It states it is the same you would use on ELISA...

28 February 2021 1,149 1 View

How to modify Johnson cook equation in ABAQUS?

I wanted to add an extra parameter to the existing Johnson cook equation in the ABAQUS simulation. How to add those extra parameters. Ref: A modified Johnson-Cook material model with strain...

28 February 2021 4,841 3 View