Why " number of views" is fluctuating here?

01 January 1970 1 9K Report

From the morning, my number of views figure is fluctuating about 100. What is the reason for this? Which value is correct?

Grzegorz Cios

I think you should address this question to RG developers here is the link:

https://www.researchgate.net/contact?type=contact_other&subject=Additional%20Support%3A%20Stats

Badges
Science topic

Similar topics
Correction

More Jayaram as.'s questions See All

How to implement monte carlo method to compute state value in matlab ?

assume there are 80 states each with a possibility of 2 actions. we have a predefined reward function. The problem is about research allocation.

30 October 2020 9,930 3 View

Does anyone has a working protocol of sample preparation for doing NMR for G-quadruplex formation in presence of a specific Metal Ion ?

I want to do NMR for my G-quadruplex forming Oligonucleotides in presence of a specific metal ion. Our lab is new to this topic and no one in our lab has experienced about this.I have tried using...

17 March 2020 8,355 2 View

I am trying to use Modified cam clay as soil model in the simulation of an excavation problem in FLAC. I am getting an error. Can someone help?

The error says "Current value of tangent bulk modulus is larger than maximum input value". Input parameters were taken from a journal. When I try changing the bulk modulus, the error message is...

08 October 2019 5,267 3 View

I need help to interpret my cox proportional model?

Hi There I was performing a cox proportional model for a cancer study in SPSS and I had this output where the Exp(B) was 0.0000064 and the CI 0 to 3.69E+51 ; p= 1 How would I report this Thank...

13 August 2019 5,054 3 View

How to create a bathymetry input file for MIKE 21?

Hi, I am learning MIKE 21 model and I would like to create input bathymetry file from GEBCO 30 Arc Second data for north coastal Bay of Bengal. Which one do I need to follow? Bathymetry or mesh...

24 June 2019 4,372 5 View

What is the different between model, architecture, framework, and protocol in computer science?

I know this question is clear but I want to know the difference between these facts especially in computer science?

31 May 2019 5,710 2 View

Why the crack propagate in that direction (to the left hole)?

Left side of the specimen is applied with fixed support and load is applied downward on the right hole. I need an explanation why the crack propagate to left hole. What i have in mind is since...

18 February 2019 2,159 1 View

Why so called dark matter is outside the galaxy?

The so called dark matter is pictured out side the galaxy. What is the reason? why cant it be a part of the galaxy itself ?

03 September 2018 155 4 View

Will someone provide me typical sorts of laboratory exercises on Machine learning?

I want to develop a laboratory module for undergraduate computer science on Machine learning. The lab should consist of a few 15-20 questions ranging from simple ones to little complex ones...

05 August 2018 1,570 6 View

How to account for the time duration of polymer immersion in solvent, in the calculations for swelling ratio?

The Flory-Rehner equation does give the relation between cross-linking density and the swelling ratio. But will there arise a difference in the swelling ratio if a polymer is immersed in a solvent...

24 May 2018 9,437 3 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

No title

I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...

25 February 2021 2,615 3 View

How Can I clain a removal of a co-author?

I would like to make a correction in a co-author in your paper which is wrong. This name is also in other papers of Kenton Ko. Zey Ko is not a Co-author . The correct name is Zdenka...

24 February 2021 3,476 4 View

How does the injection volume impact LLOQ and ULOQ in regression analysis (LC-MSMS)?

Hello, I have run into an issue that has sparkled a debate at work: is the LLOQ/ULOQ impacted by injection volume under the following circumstances: 1) Same dilution factor of all samples 2)...

23 February 2021 9,159 3 View

Difficulty in debugging code to correct error - TypeError: '<' not supported ?

I am trying with a Unet code ontained from net ...in tensorflow. When trying to predict the segmentation result with the trained and saved model with metric " iou" using "CustomObjectScope"...

22 February 2021 5,254 1 View

How to perform Haldane correction on SPSS?

I was wondering if anyone knew how to perform the Haldane correction for SPSS (this is the definition of the correction -...

21 February 2021 2,882 1 View

absorption= 1-mag(S(FP1:1,FP1:1)S(FP1:1,FP1:1))-mag(S(FP2:1,FP1:1)S(FP2:1,FP1:1)) is it correct for absorption ?

hi everyone I am simulating a unit cell structure in HFSS using Flouquet port having two modes for absorption I have used this formula:- absorption=...

17 February 2021 9,178 2 View

What is the best temperature to coat an ELISA plate?

Hello, I want to control the temperature of my ELISA plate during incubations to get consistent results. In general, what is the best temperature to coat the plate with antibody? I have been...

16 February 2021 2,377 7 View

How can I calculate the magnetic force applied from a magnet (no electrism)?

I would like to calculate the magnetic force on a Fe304 particle which is into a liquid solution . The magnet is above the solution , and there is no electricity. I found this formula : F = (V...

13 February 2021 4,770 3 View

What is the best way to do symmetry in ANSYS Fluent for flow between two concentric cylinders ?

I am working on Taylor Couette flow between concentric cylinders and the results are correct for the full case. however, I wanted to do symmetry case to improve the mesh. I have tried periodic...

11 February 2021 2,193 6 View