Why does IR2125 high side driver releases no pulses?

More Sabah Vs's questions See All

This is my new article?

Phenotypic and prevalence correlation with recurrent KRAS G1...

12 July 2024 3,031 0 View

the increase in ΔS0 from AC1 to AC2 (67 J/mol to 143 J/mol) ?

If we compare the values, the increase in ΔS0 from AC1 to AC2 (67 J/mol to 143 J/mol) indicates that the amount of adsorption is higher for AC2 compared to AC1. This increase in entropy means that...

10 June 2024 9,287 0 View

How to create a ridge waveguide at 70-degree angle by Rsoft software ?

Hi everyone, in Rsoft there are choose to select ridge waveguide, However the profile index is step ( 90 degree-angle ) so, i want to create ridge waveguide at 70 degree . could you please guide...

07 September 2023 1,256 1 View

Why coercivity increases but anisotropy constant and crystallite size decreases when tin is doped in Nizn ferrite nanoparticles?

why coercivity increasesa but anisotropic constant and crystallite size decreases when tin is doped in Nizn ferrite? Is this transition from single domain to multi domain behavior?

11 August 2023 8,973 1 View

Representative volume element and periodic boundary conditions ?

Hello all. My question goes back to the use of representative volume elements for modeling structures and boundary conditions needed to solve RVE in a finite element model. Assume that there is a...

12 July 2023 4,775 5 View

Why crystal size decreases initially and then increasing by increasing concentration of smaller ionic radii dopant in ferrites?

What happened when small amount of tin is doped in nickel zinc ferrite initially the crystallite size decreases but with an increasing ratio of dopant (tin) the crystallite size increases why?

04 June 2023 8,785 1 View

Question about common ground?

I have an experiment set up where the device under test DUT requires DC power supply. But the output of the device needs to be connected to an oscilloscope. I am apprehensive about damaging any of...

17 May 2023 251 0 View

Peace, please, I want information about the activation energy and its relationship to adsorption?

15 April 2023 7,061 1 View

How to calculate surface area using Langmuir relation?

How to calculate surface area using Langmuir relation surface langmuir

04 April 2023 6,459 3 View

The effect of NaCl ?

The effect of NaCl salt gives a positive value in decolorization and water treatment. Is the effect of pH or surface carbon effect positive or negative?

21 March 2023 3,938 1 View

What are some signs that an ECM is overfitting the Nyquist plot?

What can you look for to know that the circuit model being used is overfitting the data. How do you know when overfitting is occurring?

31 July 2024 7,425 0 View

Can a shoot-through event of a tri-state digital buffer cause momentary Hi-Z state?

// interested in the difference between floating events and short circuits.

22 July 2024 6,565 0 View

Concatenation of consciousness: lessons from motion perception?

Gestalt psychologists have proposed many ways in which items are concatenated within a single block of time so that perceptual elements can be combined into complete objects as defined in space...

29 June 2024 2,441 1 View

Hello friends. Here, can someone help me in connection with hybrid circuit breakers in both ac and dc current, how to simulate different parts of the?

Hello friends. Here, can someone help me in connection with hybrid circuit breakers in both ac and dc current, how to simulate different parts of the breaker in LTSpice or PSpice? And how is the...

18 June 2024 1,486 0 View

Do you have any research or invent about IR sensors?

I want to record a analog circuit between control and power circuits as innovation. My control circuit is IR sensors with bulb size 10mm (its max current to support power circuit is 100m[A] DC)and...

05 June 2024 4,085 4 View

For best fit equivalent circuit model through Nyquist plot why fitting is not good at initial and end of the semi circle arc?

I am selecting frequency range from 10Hz to 10MHz for EIS study of fruit quality, when i tried to fit nyquist plot, I am not able to get best fit when select full range (10Hz to 10MHz) of...

20 May 2024 5,470 0 View

How to reduce notches in input AC voltage for Totempole Power factor Correction circuit?

Respected readers, I am working with a totem pole PFC circuit. In an experimental study, I face a problem of high-frequency notches in source voltage (Yellow one). I found an explanation behind...

14 May 2024 6,692 6 View

What is the physical meaning for the following equivalent circuit?

Can anyone help me to find out the Rs = Solution resistantce and Rct= Charge transfer resisistance of the following equivalent circuit. specifically, which R should I take as Rct. I got this...

12 May 2024 4,358 2 View

How to show the differences between the output voltages on the graph?

Can someone help me, I don't know how to show the differences between the output and input voltages on the graph. I have two voltages at the input: Vin1 and Vin2, at the output I have Vout1 and...

09 May 2024 3,243 0 View

SIW horn antenna in CST Studio adding vias?

Hi im making a SIW horn antenna in CST studio and im lost on how to add vias at an angle instead of a linear line. Its along the flaring, 17 degrees. Does anyone know how to do that?

04 May 2024 6,626 2 View

Andrey Pavlov

Try to replace ERR resistor with capacitor

Sabah Vs

@Andrey Pavlov

i have tried that too.

Maybe your driver is broken?

Nimmanapalli Rajesh

Try err resistor and capacitor it works.

thanks everyone,i found out the issue,it was a ground problem

Rahul Rahul

hey i'm facing same problem.

can u explain what has u done