Why ACI 549.13 limit the ultimate strain of FRCM? and is there any relation to this limit to creep?

06 August 2020 0 8K Report

ACI 549.13 limits The effective tensile strain level in the FRCM composite material attained at failure according to the following equation εfe = εfd ≤ 0.012

Badges
Science topic

Similar topics
Engineering

More Ayman Shamseldein's questions See All

Good evening everyone can anyone send me SMC files of earthquakes of different intensities for a simulation on Plaxis 2D?

Good evening everyone can anyone send me SMC files of earthquakes of different intensities for a simulation on Plaxis 2D. Thanks

02 March 2024 4,362 1 View

Was the name of a researcher from Helwan University published on the website of most of my articles?

أخاطب السيدة المذكورة باسم Sarah Ayman بحذف اسمها من على الأبحاث الخاصة بى لأن هذا يعد انتحال علمى وسوف نبلغ جامعة حلوان بذلك

25 February 2024 7,614 1 View

We ask you to kindly change the information of the first name written incorrectly?

We ask you to kindly change the information of the first name written incorrectly as Sarah Ayman to the correct name as listed in the article, Ayman S Taha. Sincere thanks and appreciation.

25 February 2024 8,634 1 View

In the flotation process, what is the future effectiveness of using an activator reagents on copper oxide surface?

I know that many reagents are used as activators or enhancers (such as ammonium salts and so on) in copper oxide minerals processing to facilitate their flotability during the flotation process....

28 December 2023 2,694 0 View

Transfection of neuroblastoma cell line (SHSY5Y) for RNA collection??

Usually neuroblastoma have low transfection efficacy (5-10%) when transfected with Lipofectamine 3000. So, this time I have tried electroporation with this condition, poring pulse: 175V, 2.5ms,...

23 August 2023 1,962 2 View

How to calculate the optimum annealing temperature for PCR?

15 August 2023 2,205 5 View

Why do supercapacitors sometimes struggle to reach the voltage cutoff at low current densities?

Any solid reference to why sometimes, especially at very low current densities, it takes too long to reach the charging voltage cutoff, while discharge takes place much faster?

03 July 2023 5,583 3 View

What are the most prominent problems that chemistry laboratories in secondary schools suffer from?

give me 3 problems

11 April 2023 6,197 5 View

What are the new technologies in green chemistry?

Green chemistry

11 April 2023 8,194 2 View

What is the best adsorbent material to replace commercial carbon?

Adsorption material

11 April 2023 9,427 0 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

What may be the reasons for failures of Tube toi Tube Sheet Joints in Boiler Drum ?

We have observed that tube to tube sheet joint leaked in our boiler and needs to overcome same by knowing the root cause.

08 August 2024 3,161 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Research Methodology - Impact of Corporate Reputation on Stakeholders Behaviors?

Please can anyone support with the survey questions based on RQ measures and propose how to do it in FMCG industry and include as well the role of brand equity Thanks

06 August 2024 949 0 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

Anyone having idea about VN primer for miRNA primer design ?

How to design VN primer to attach with universal reverse primer

05 August 2024 2,116 3 View

Can anyone explain why there is not any color bands in the middle portion of the tensile coupon?

Details of the Analysis. Static Analysis Composite Layup Continuum Shell Elements FRP Material (Elastic and Hashin Damage)

03 August 2024 8,538 4 View

What are the limitations and challenges of using machine learning for predicting concrete compressive strength in practical applications?

Machine learning (ML) has shown great potential in predicting the compressive strength of concrete, an important property for structural engineering. However, its practical application comes with...

03 August 2024 2,546 2 View

Should I remove an item from a scale to raise Cronbach's alpha and McDonald's omega or is it better to leave it if they are both over .7 already?

Hello! I have this scale which had 10 items initially. I had to remove items 8 and 10 because they correlated negatively with the scale, and then I removed item 9 because Cronbach's alpha and...

01 August 2024 4,606 7 View