Level 1 pre-post multilevel regression: Panel data or ANOVA approach?

Dear colleagues, I am currently teaching myself in multilevel analysis using educational data. I found few to zero literature on basic analysis methods. In my context we frequently use level-1...

17 February 2021 9,378 5 View

Reliable and Valid Instrument for Causes of Medical Errors?

Is there any questionnaire/survey that measures the causes of medical errors? Example: physician negligence vs. systemic issues. Looking for a reliable and validated instrument. Thank you!

15 February 2021 2,874 4 View

Should the AUC in a concentration-time graph of a subcutaneous implant be roughly the same for poeple?

I have 2 concentration time curves of a subcut drug implant. the first group has a peak around the 50 day mark where as the second group does not. Both groups received the same implant by the same...

10 February 2021 2,305 3 View

Software for flow cytometry-like gating of data sets?

I am currently trying to do image based cytometry from fluorescence microscopy images. From the images I extract data such as cell size and a number of fluorescence intensities. Is there any...

09 February 2021 6,278 1 View

Can A. thaliana splice algae genes?

24 January 2021 329 2 View

Does long term preservation (10years) of Collembola in 99% Ethanol affect recovery rate of extraction by flotation?

Hello! I am currently developing an automated counting approach using Fiji to count Collembola from pitfall trapped samples that have been stored in Ethanol (99%) since 2010. I use flotation (tap...

13 January 2021 659 2 View

Co-stain Lectin PNA FITC conjugate with an uncojugated primary antibody?

Hello, I am planning to stain retinal tissue sections for IHC and want to co-stain cones and rods. For this we plan on using a Lectin PNA From Arachis hypogaea (peanut), FITC Conjugate for cones...

12 January 2021 583 1 View

How to use Abaqus USDFLD subroutine to vary stiffness?

Hi I have a problem where I am trying to vary the stiffness spatially across a structured interface. The whole idea is to vary the stiffness vertically, with a bulk stiffness of 8GPa decreasing...

06 January 2021 262 3 View

I really need help with cov-2 pseudotyped lentivirus production. Support?

Hi, i'm desesperate. i'm trying to produce lentivirus usinf BEI resources kit NR-52948. 24 hours after transfection i detect a massive GFP expression in my 293T cells. After 72 hours i filtered...

30 December 2020 9,889 6 View

How can i estimate the total phenolic content from a plant extract?

Suggestions and recommendations are welcome. A protocol used and experience would also be helpful.

25 December 2020 9,807 4 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How relevant is Mini slump cone?

for all the rheology researchers, my question is, how relevant is a mini slump cone (smaller than a standard 50 cent rheometer). currently based on testing, the thickness of slumped material is...

26 February 2021 3,668 1 View

Stress/strain tensors decomposition ???

25 February 2021 6,760 1 View

How to reduce residual stresses in MD simulation?

I am working on a preparation of representative polymeric structures of some popular polymers, such as polyimide or PTFE for MD simulation, during which a single nitrogen or oxygen atom will be...

24 February 2021 8,105 3 View

Suggestions for occupational stress surveys?

I am currently writing a masters thesis on reasons for occupational stress in the early childhood classroom, and want to include a short survey assessing participants work-related stress levels. I...

24 February 2021 8,678 2 View

The most suitable method to calculate the stress intensity factor in the presence of contact between the crack lips?

I'm trying to study cracked structures under a compressive load taking into account contact between the crack lips. I would like to know if the method of extrapolation by displacement remains...

21 February 2021 8,694 4 View

How to assign two different material/section properties in Abaqus(UMAT)?

Hi everyone, I am conducting a non-linear multi-layer pavement structure analysis which is a stress-dependent. So far, I am able to define the nonlinearity for one soil layer for its resilient...

11 February 2021 9,607 3 View

Are there any exception like work hardening in metals elastic limit due to dynamic loading?

The samples made out of spring steel are taken from same lot. The specimens were shaped following heating to forging temperature - Forming- Hardening -Tempering methods. After storage of almost 6...

11 February 2021 952 6 View

How to write cyclic loading in OpenSees?

Hi there, I'm having trouble with adding cyclic loading in OpenSees software. My task is to model a reinforcing bar under cyclic loading and compare the response with the experimental results....

04 February 2021 8,158 1 View