Who can i prepare a ceramics coating on aluminium alloy?

More Zainab Raheem's questions See All

What is the solution to linear shrinkage in composite gel films?

linear shrinkage in composite gel films

04 May 2019 8,246 1 View

What is the gel material used in sol gel ?

gel material used in sol gel

03 April 2019 8,288 1 View

Who we can measure the permeability of water using polymeric thin films?

the permeability of water using polymeric thin films

01 January 1970 7,500 2 View

Why cathode is positive in rechargeable batteries?

li iion battery

01 January 1970 7,933 1 View

What is the best detox?

i think lemon and mint

01 January 1970 6,043 1 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

How does grain and grain boundary affect the ceramic when studying its dielectric properties?

I am not able to get good literature and the physics behind how first these grains and grain boundaries arises out of no where when we make a pellet to study its dielectric properties and then how...

07 August 2024 5,177 3 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

Why is my ASO degraded quickly on agarose gel?

I have been working on Red blood cell-derived extracellular vesicles as Antisense Oligonucleotide (ASO) carriers. We normally run agarose gel to quantify the loading efficiency. I used naked ASO...

06 August 2024 3,130 2 View

I'm optimizing a tetra-ARMS PCR protocol with amplicon sizes: 165bp, 123bp and 93bp. Why, in the gel, only 165bp is visible while I'm expecting all 3?

It's an end-point PCR protocol. I'm using 1.5% agarose gel with SyBR Safe dye and TBE as a running buffer, visualization on BioRad XR+ system. I was primarily thinking of primer efficiency,...

01 August 2024 4,673 4 View

How select composition for ods-high entropy alloys?

31 July 2024 2,795 1 View

What is the reason I get 400nm nanoparticles using an extruder with 200 nm membrane for cell membrane coating?

I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...

30 July 2024 3,294 3 View

I am trying to obtain microstructure for Mg-Zn-Sn alloy?

Any suggestions with respect to etchant composition and holding time?

27 July 2024 6,925 2 View

Mahmood Hameed M.

dear Zainab Raheem ;

The ceramic coating on the Aluminum surface can be prepared by sol-gel method using the ratio of the silica sol TOES: H2O : EtOH of 1:1:10, as detailed in the reference;

Article Preparation of ceramic coating on aluminum alloy by sol-gel method

Zainab Raheem

thank you