While using GeoPIV RG, what is the minimum values can I go for CC ZNCC-seed and CC ZNCC-min-tol? How to reduce the standard error after callibration?

02 February 2018 0 8K Report

According Stanier et al. (2015), we need to evaluate various parameters CC ZNCC-seed , CC ZNCC-min-tol and standard error in order to deem the PIV results were correct i.e. 0.9, 0.75 and standard error less than 0.5 respectively. Can I have some relaxation in this values as instead of very small scale centrifuge tests mine is 1g model test of comparatively greater dimension of 1.8m by 1.2m.

Badges
Science topic

Similar topics
Chemistry, Organic
Organic

More Rupam Saikia's questions See All

How does one calculate interfacial heat transfer by using data from Fluent simulation for a subcooled flow boiling model?

I am trying to simulate subcooled boiling flow through an annulus using Fluent. Is it possible to get the values of interfacial heat transfer coefficients from either FLUENT report or CFD post?...

31 October 2020 3,599 3 View

How to determine presence of Cross Sectional Dependence in Panel data?

Hello everyone. I have a panel data of N=30 and T=20. It's not exactly a case of small T and large N. Can I use the command xtcsd, pesaran in stata to check for cross sectional dependence? I am a...

07 October 2020 7,676 13 View

What are the LoRa WAN practical application?

LoRa is a wireless technology that offers long range , low power and secure data transmission for M2M and IoT applications. But in present era of mobile 4g and 5g what may be effective...

12 August 2020 515 4 View

Is it possible to map Von Mises stress of a deformed model to a undeformed model of similar mesh, material property and boundary conditions in ABAQUS?

I want to map the Von Misses stress generated for a 3D model in supposing Job-1, to run a new job on a similar CAE model but undeformed with similar material properties, mesh, boundary condition...

15 December 2019 8,385 2 View

Can we use quartz cuvette to measure absorbance at 1000nm???

Hi, I am measuring the absorbance of Cu2+ in solution in a scan mode in CARY 60, Agilent. Absorption maxima of Cu2+ in solution is 800nm. I want to know if I can use conventional quartz cuvette...

26 November 2019 9,166 5 View

Hello colleages, What is the procedure to publish a book chapter in springer, elsevier or any other publishers?

Can we publish book chapter only when we get the inviation or Is there any procedure to contact the editor of the publishing agency for publication of the book chapter

15 September 2019 9,370 16 View

How to calculate Genotypic and Phenotypic Correlations?

I want to correlate gene expression values of a same gene across different genotypes to check wheather the gene is closely correlate or least correlate or negatively correlate with the genotypes?...

09 June 2019 9,148 4 View

How to implement traction separation relationship in vumat?

i am trying to implement a simple VUMAT traction separation code in my cohesive zone model by using the relation, separation=straininc*charlength. but while implementing i am getting the error as...

30 September 2018 1,332 3 View

How to calculate the quantum yield of fluorescent nano-dots?

I have found in literature that people are using quinine sulfate as a reference to calculate the quantum yield of a fluorescent material. It is having a quantum yield of 54 % at 375 nm excitation...

15 August 2018 5,952 4 View

How to calculate a similarity/distance matrix from multiple binary matrices generated from PCR amplicons by different Primers ?

Say I am doing RAPD PCR on some sample sets with 10 different primers, so that I will be generating 10 different binary matrices (based on presence or absence (as 0 and 1) of bands on...

09 March 2018 179 4 View

Image Processing and classification using keras/Tensorflow?

Do you have some recommendations approaches on Image processing and classification of plant diseases using TensorFlow/Keras?

02 March 2021 1,493 4 View

Which SAR dataset to use for generating coherency matrix and performing target decomposition (Description) ?

Working on chandrayaan-2 DFSAR data, there are three datasets available: 1) Slant range image data product: The slant range complex image file. Each pixel is represented by two 4-byte floating...

02 March 2021 8,481 3 View

Discrete Phase model (DPM) particle break-up has particle size limits during particle tracking?

Hello, I am currently working on simulating water droplet partciles in a closed room. When I use uniform particles, without "particle break-up", I can carry out the simulation without any problem....

02 March 2021 3,053 2 View

Do you know any MR image dataset?

I would like to research on MR images (0.5T and 3T). Can you please suggest some websites that I can download dataset including both 0.5T and 3T MR images? Thank you.

02 March 2021 7,735 3 View

Distribution of particles in metal matrix?

How would define the "good" and "poor" distribution of particles within the matrix. Is there a quantitative solution to assess the distribution of the particles, which then having denotation of...

28 February 2021 7,397 8 View

Is there a deep reason for using the squared modulus of the wave function as the probability density of the existence of the particle?

I think we were all surprised at the first time we got to know quantum mechanics that the squared modulus of the wave function is the probability density of the existence of the particle? The role...

28 February 2021 6,282 9 View

Zno nano particles colour changed from white to grey in process of calcination any suggestions?

In the formation of Zno nano particles process, after drying at 120 degree C, my zno nano particles are completely white but when i calcine it for 450 degree C it converts into grey colour. i...

26 February 2021 2,435 4 View

Why there are two peaks while using the mie plot of Silver nanoparticle?

Hi, I am trying to learn the theoretical modelling of silver nanoparticle using the Mie scattering theory. After that, I discovered a software named Mieplot developed by Philip Laven, where it...

25 February 2021 7,493 6 View

Quantifying leaking DNA from bacteria - what's the secret?

Hi, all! I need to determine if my treatment causes membrane damage in bacteria (S. aureus and E. cloacae), but I cannot use a fluorescent probe such as PI and similar ones because my compound is...

24 February 2021 2,006 2 View

How can I verify my centrifugal fan design for electric motor cooling?

I have radial blade centrifugal fan design which will be mounted on exhaust side of electric traction motor. The fan will be mounted on same motor shaft inside the housing. How can I verify that...

23 February 2021 2,390 3 View