which steel can be treated by case hardening and why ?

01 January 2018 0 679 Report

Heat treatment is important process for steel to improve the mechanical properties, case hardening is one of them .

Badges
Science topic

More Saad Kariem Shather's questions See All

What is your opinion about magnetic abrasive finishing (MAF) and is it suitable for manufacturing parts in medical applications?

Magnetic abrasive finishing (MAF) is one of advanced process which is used to machine and enhance the surface layer of parts .

10 November 2018 4,028 0 View

What is the value of the limited depth to which form errors, tapers, looping can be corrected by MAF process?

Which depth can be reached by magnetic abrasive finishing (MAF)?

10 November 2018 1,579 0 View

Are schools providing students with suffcient, well-trained guidance counselors?

Before university Are students prepared for college?being prepared for college means,at a minimum, having the English and math knowledge and skills to succeed in entry-level, credit-bearing college

04 May 2018 10,250 18 View

Do you recommended to use only the textbooks in Lecture ?

The textbooks in lecture.

04 May 2018 7,337 3 View

Are you alarmist about your country future?

many peoples were alarmist about their countries (decreases of water resource, natural resource, oil resource...)

03 April 2018 4,827 19 View

What have you learned from the process of doing your PhD?

03 April 2018 2,811 14 View

What are the limitations you have faced while writing PhD thesis?

The limitations in writing PhD thesis.

03 April 2018 2,869 23 View

How to convert mild steel into high carbon steel ?

Convert mild steel into high carbon steel

02 March 2018 4,044 2 View

What are the software’s which can be useful in manufacturing unit?

02 March 2018 9,943 7 View

What is the Difference between Production and Manufacturing?

Difference between Production and Manufacturing?

02 March 2018 1,444 7 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

How does grain and grain boundary affect the ceramic when studying its dielectric properties?

I am not able to get good literature and the physics behind how first these grains and grain boundaries arises out of no where when we make a pellet to study its dielectric properties and then how...

07 August 2024 5,177 3 View

Why does my protein refolded to beta sheet during thermal denaturation analysis?

Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...

06 August 2024 1,989 3 View

How to heat polymer for about 130° without oil bath ?

is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it

06 August 2024 947 1 View

Could dyes amplify the spectrum of light to a specific wavelength?

I am interested to know the behavior of dyes toward light. Specifically, Blue dyes re-emit the spectrum, especially from the green zone (known as principal in LED lamps, and blue dyes are known...

05 August 2024 3,290 1 View

What should I do with parameters that are not relate to my simulation in MyLake model?

I want to Estimate surface heat fluxes using MyLake, but I don't have all the initial values in model parameters section and other sections,is there a way?

04 August 2024 1,537 1 View

Can't spin-orbit coupling(SOC) be included in optical properties calculation in CASTEP?

I am currently using CASTEP version 2020. When I want to run optical properties calculations with spin-orbit coupling(SOC), I encounter the following error in a pop-up window before the job gets...

02 August 2024 2,890 0 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

29 July 2024 7,714 4 View