09 September 2015 0 5K Report

does follicle liquor heavier than granulosa cells in the same volume?

More Anggadia Wardani's questions See All
Why do some obligate parasitic plants and insectivores have clorophyle?

For example: 1) Loranthus sp. is an obligate parasitic plant that depends its nutrient supply on other plant's transport system. 2) Venus sp. is an insectivorous plant (heterotroph) However, they...

03 April 2018 8,636 2 View

Where did the leucocytes gone during estrous cycle?

I recently learn vaginal cytology in estrous cycle. as i know, there are abundant of leucocytes in metestrus phase and the amount of leucocytes decrease until disapear in estrous phase. where did...

10 November 2014 1,675 0 View

Is this the vesicula seminalis or uterus masculinus?

I am studying the "Guinea-Pig" male reproductive system. After dissection, I found a structure (picture below) that is explained differently in various places in the literature. Some claimed it...

10 November 2014 3,037 19 View

Can anyone tell me what kind of cell is this?

I found this cells (picture below) when i did hemocytometry of Cavia sp.'s blood with Turck reagent. But it can't be found in smear preparation with Giemsa staining. It was big ovoid cell, central...

04 May 2014 2,342 11 View

Similar questions and discussions
MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Why does blocking with my immunogenic peptide cause nuclear fluorescence in ICC?

Hi all, I am validating a polyclonal antibody raised against human ANT4, through WB and ICC. In most of my controls, the antibody shows very little off-target binding, but when I pre-incubate the...

03 March 2021 5,999 3 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

Where can I find life cycle inventory or assessment of non woven materials?

Dear network, I am looking for the LCA or LCI or at least the energy balances of the non woven fabrics process for my master project, in specific for natural fibers, yet I have found...

02 March 2021 9,662 1 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close