Which is the overbending of AA6063 aluminum tubes necessary to obtain a specified angle?

23 April 2015 0 5K Report

Someone knows which is the over bending of AA6063 aluminum tubes necesary to obtain an specified angle? I answer because the material has always an elastic recuperation?

Badges
Science topic

More Daniel Martinez Krahmer's questions See All

How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?

09 August 2024 7,718 0 View

H-index issues?

Hi Sir/Madam, I would like to know why my h-index is stuck to 15 despite the number of new publications added. Could you explain me how marks are granted. Best, Daniel

28 July 2024 2,607 2 View

I'm looking for a tool to evaluate the risk of bias in... Are there any recommended applications or platforms?

Dear researchers, In a systematic review (not a meta-analysis) compiling studies on various diagnostic systems against a specific pathogen. The most relevant parameters evaluated are the type of...

03 July 2024 9,069 3 View

What is the current usage and patronage of parks and greenspaces by older adults (aged 65+) in Salford? How does the frequency of older adults' visit?

What is the current usage and patronage of parks and greenspaces by older adults (aged 65+) in Salford? How does the frequency of older adults' visits to parks and greenspaces in Salford relate to...

22 June 2024 7,616 1 View

How can we compare SENTINEL vs LANDSAT for NDVI?

A question to see who can answer it. If the red and infrared bands of the satellites are...

16 June 2024 2,249 1 View

ImageJ Concentric Circles?

Hi there! We are trying to use the Concentric Circles Plugin on ImageJ to determine signal intensity in neurosphere cryosections after immunocytochemistry/confocal analysis. We determined the...

12 June 2024 7,332 0 View

How do i use researchgate to cunduct literature review ?

I am a first-time researcher in the field of nursing and i would like to conduct research about knowledge and attitude towards prevention and spread of tuberculosis.

11 June 2024 3,821 2 View

Is there any possibility for cultured mouse neurons more than 7 days?

Dear colleagues, I'm planning to start neuron mouse co-culture with astrocyte and microglia but I heard that it's difficult to keep it up. Any advices?

27 May 2024 4,905 3 View

What are some possible technical failures during lentiviral packaging using HEK293T?

I'm having trouble packaging lentivirus in HEK293T using pCMV, pMDG, an shRNA and polyfect. I normally seed 1.5 x 106 HEK293T cells in 60 mm on Day 0, which translates to about 60 to 70%...

20 May 2024 9,067 1 View

What is the minimum amount of liquid and beads I can use for bead-beating in a 2ml vial?

I am planning to extract DNA with QIAamp Mini DNA extraction kit (Qiagen) from DNA Shield microbiome preserved samples. My samples contain small amount of cell, so my goal is to reduce the loss of...

14 May 2024 2,291 2 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

Best mask design for metal deposition aiming build a Perovskite solar cell device?

What types of mask designs for metal deposition, to be used in a PVD system, are best suited for perovskite-based solar cells?

31 July 2024 4,835 3 View

How select composition for ods-high entropy alloys?

31 July 2024 2,795 1 View

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

29 July 2024 7,714 4 View

I am trying to obtain microstructure for Mg-Zn-Sn alloy?

Any suggestions with respect to etchant composition and holding time?

27 July 2024 6,925 2 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

Can you recommend provider Intermediate laboratory test for hydrocarbon, polyethylene & polypropylene?

Accredited laboratory of JV "Uz-Kor Gas Chemical" LLC (Uzbekistan) is looking for providers to conduct interlaboratory comparison tests on gas chromatographic analysis of hydrocarbons (component...

25 July 2024 8,108 0 View

Can we eliminate the stress singularity at the tip of the crack by manipulating the elastic constants?

The aim of the research here is to prevent the propagation of the crack in the fabricated elastic medium with useful applications.

25 July 2024 9,976 3 View

Is there a good macro photography kit for on-site metallurgical investigation?

I am looking to purchase a photography kit for onsite metallurgical investigations, such as capturing photos of worn areas, hot tears, cold tears etc. Could anyone suggest me a good...

22 July 2024 3,490 2 View

Concentration of gelatin as brain model ?

I am using gelatin to model mechanical properties of brain tissues in-vitro. Do you have any suggested concentration ? Thank you so much.

19 July 2024 3,095 0 View