Which is the maximum temperature for using a 95%Pt, 5%Au crucible ?

More Miguel Oscar Prado's questions See All

DFT calculation data: Glassy structure cluster database - can anyone help?

In our lab we plan to perform some DFT calculations on glasses. Is there available any database of cluster of atoms with a glassy structure (silica or any other glass), which we can take as...

06 July 2013 2,332 11 View

What thickness need for ITO to use as conductive layer?

I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...

01 March 2021 395 3 View

Does anyone know HRM channel in a 2 plex QIAGEN Rotor- Gene Q qPCR can be used as a separate channel?

I am going to have 3 different probes in my qPCR work that I am going to do. But I realized that the machine we have in the lab is a Rotor-Gene Q 2plex HRM Platform, saying it has green, yellow,...

01 March 2021 8,544 1 View

What is the state of the drug inside solid lipid nanoparticles (SLNs)?

I am a little confuse with the mechanism of solid lipid nanoparticles (SLNs). The main point of encapsulating drugs into SLNs is because some drugs have low solubility in water. Therefore, SLNs...

01 March 2021 3,703 3 View

Glass fiber content in a gypsum board ?

Any idea on how to get the volumic ratio of glass fiber in a gypsum board ? Thank you for your help !

01 March 2021 2,501 3 View

Can water be extracted from Olivine?

I have always been interested in geology and wondered about how unique structures of materials behave in different circumstances. I stumbled upon Olivine, the magnesium iron silicate, and heard...

28 February 2021 7,330 4 View

Concrete compressive strength databases?

I am looking for datasets similar to this one: http://archive.ics.uci.edu/ml/datasets/Concrete+Compressive+Strength I am looking for concretes with different types of aggregates (Recycled,...

27 February 2021 6,801 3 View

How to properly calculate the fluid solid heat transfer between polypropylene matrix and glass fiber in a porous medium?

I'm building a cfx model of thermoplastic pultrusion process on ansys and i have a doubt on how is the proper way to set this parameter in a porous medium

24 February 2021 1,915 1 View

How to properly calculate Interfacial area density in a porous domain?which are possible value for glass fiber?

I'm doing a cfx simulation of a multiphase flow in pultrusion and i set the Interfacial Area density in the heat exchange of a porous medium in this way IAD=Total fiber lateral surface of fiber...

23 February 2021 6,043 1 View

How can I measure the thickness of thin layers deposited on textured glass susbtrates?

I want to measure the thickness of aluminum oxide and titanium oxide layers deposited on textured glass substates. The layer thicknesses are typically below 100nm.

21 February 2021 5,465 4 View

How can I measure the surface interaction or surface interfacial chemistry between polishing abrasives and upper surface of substrate ?

I am working on polishing abrasives. I need to do few characterizations ? which can provide the on time surface chemistry of substrate with polishing abrasive during optical polishing. I would...

18 February 2021 5,319 3 View

Miguel Oscar Prado

Thank you Simon!

Manohar Sehgal

If Pt is a must, better use any one of the following:

1.95/5(Pt/Ru); Vicker hardness (130-210); up to (1780-1795C).

2.95/5(Pt/Co) ; Vicker hardness (135-270); up to( 1680-1770)

[slightly ferromagnetic].

3.90/10(Pt/Ir) ; Vicker hardness (110)0 ; up to1780-1800C.

Otherwise there are many non Pt crucibles which can be used even up to 2500C.

If asked; can send their % composition and the maximum temperature limits.