Which are the possible peaks in IR for Fe3O4 ?

08 February 2019 1 10K Report

the absorption peaks at 568 cm-1 belonged to the stretching vibration

mode of Fe–O bonds in Fe3O4 possessed absorption peaks presented at 1603 and 1278 cm-1 should be attached to the stretching vibrations of C = C

Badges
Science topic

More Suryabala Jagadale's questions See All

I have CHNS analysis in wt %. n van krevelen diagram how we calculate atomic H/C and O/C ratio?

please help me to calculate H/C and O/C ratio?

11 August 2021 5,593 2 View

Oxidation by KMnO4 ?

Please suggest the reaction mechanism for oxidation of CH3 group attached to benzene ring by KMnO4 . i.e oxidation of toluene to benzaldehyde in the presence of KMnO4.... suggest reaction mechanism.

26 September 2019 9,858 3 View

How should one prepare sample for TEM analysis?

I have coated metal oxide nano sheets on carbon fiber paper and I want have TEM analysis of the same sample. Could anybody tell me how to prepare sample? Thank you.

02 November 2014 7,053 10 View

Melt curve problem in qPCR?

Do these peaks in the curve indicate primer dimer or non-specific products?

01 August 2024 7,466 0 View

How to improve peaks separation in HPLC?

Hi everyone, I'd like to better separate two close peaks coming from a bioconversion sample, I'm currently using a C18 KromaPhase 4,6mm Ø.I. SCHARLAU, particle size (µm): 10, pore size (Å): 100,...

30 July 2024 435 3 View

How can we conduct DFT for solutions or mixtures ?

Can we conduct DFT studies for Ionic Liquids with Amines at various concentrations? If so, how can we proceed with these studies? Additionally, what parameters, besides IR, NMR, and HOMO-LUMO, can...

18 July 2024 319 1 View

What does an additional peak in FTIR between 3100 and 3300 nm affect the quality of the material, benzethonium chloride USP??

I do not know much about FTIR! The material Benzethonium Chloride USP was compared to a reference standard in regards to FTIR, as per the USP testing: Identification B. Infrared absorption (FTIR),...

16 July 2024 6,918 7 View

Validated HPLC method for the estimation of the Amphotericin B ?

During the release test of Amphotericin B using 1% Tween 80, i observed three peaks even in the standard. The first peak consistently yielded results around 500%, while the other peaks showed...

08 July 2024 1,330 0 View

Why there are no peaks at downfield NMR of Cobalt and Nickel complexes?

I synthesized some paramagnetic cobalt and nickel complexes (expected to be Co(II) and Ni(II)) using a bidentate ligand - N of pyridine ring (aromatic) and O of P=O (aliphatic), and I obtained...

03 July 2024 3,410 4 View

I have NMR,Mass spec,IR and uv of a mixture of three unknown compounds from natural products.I am attaching the data who can help me elucidate?

I isolated a mixture of three compounds from the stem bark of a plant . I have NMR, Mass spec, IR, and UV data. There are a lot of things I can't make meaning out of. Kindly help me with the...

02 July 2024 9,531 4 View

How can I put small FWHM in CasaXPS?

I'm trying to fitting Cu Auger peak into various state (Cu0, Cu+, CuI etc..) In Cu0, one of the peak's FWHM is 0.84 but when I try to enter smaller value than 0.89, "input error" is occured. How...

02 July 2024 4,932 3 View

What is the reason of appearance of 2 or 3 peaks in zeta potential analysis of sample?

Hello I have prepared metal nanoparticles and did zeta potential. Normally there is a single peak in sample but now there are 3 peaks. I prepared sample for analysis first I prepared 10 mg/mL...

30 June 2024 1,063 4 View

EDS or EDX concetration finder?

Hello everyone, I'm facing an issue with EDS software that prevents me from obtaining atomic or weight percentages for my scan. However, I do have access to the raw data, which shows intensity vs....

29 June 2024 6,664 14 View